JVC ca-mx55mbk User Manual

| CA-MXS5SSMBK
Using the Timers
Setting the Clock
The clock will be displayed even when the system is turned off. Pressing
the TUNING/TIMER/DIMMER button ( < or > ) will switch between two
brightness levels for the clock.
1.
Press the CLOCK ADJUST button on the Tuner.
The hours digits blink.
CLOCK ADJUST
=)
. Pressthe TUNING/TIMER/DIMMER button ( < or P )tosetthe hours
digit.
TUNING/TIMER/DIMMER
cr)
Press the > button to increase the hour, and press the < button to
decrease the hours.
To enter a new hour digit, press the CANCEL button and repeat step 2.
. Press the MEMORY button on the Tuner.
MEMORY
This sets the hour portion of the time.
The minutes digits will blink.
. Press the TUNING/TIMER/DIMMER button (<orP) to set the
minutes digit.
It's a good idea to set the minutes digits one minute ahead. Then you
can start the clock when it reaches the set time exactly (according to the
correct time from the TV, radio, or telephone).
To enter a new minute digit, press the CANCEL button and repeat step
4,
. Press the MEMORY button.
The clock starts as soon as you press the MEMORY button.
Caution! If there is a power failure, or if you unplug the stereo, the clock
time will be lost. Repeat steps 1-5 when power is restored.
Using the TUNING/TIMER/DIMMER button to change luminosity of
time display by two steps under STANDBY status.
» : Increases luminosity
: Decreases Juminosity
Setting the Timers
With the timers you can make tape recordings of broadcasts, CD’s, or tapes
when you're not around. You can also play these music sources at
specified times without recording them.
Use TIMER 1 and TIMER 2 record a radio broadcast when you’re not
home, or late at night when you're asleep.
Use the DAILY timer to record a broadcast that occurs at the same time
every day.
The procedure for setting TIMER 1, TIMER 2 and the DAILY timer is the
same. You need to tell the system:
— The name of the timer (TIMER 1 , TIMER 2, or DAILY).
— The time the timer should turn the system on.
— The time the timer should turn the system off.
-—— The source the timer should turn on (Tuner, CD, or Tape).
—— The volume level that should be used during recording or playback.
Note:
The clock must be set to the correct time for the timers to be effective.
Caution! Do not operate the remote controller when you are programming
the timer.
Choosing a Timer
Press
the
TIMER
1,
TIMER
2,
or
DAILY
button
on.the
Tuner
to
select
a
timer.
This
puts
the
system
in
the
Timer
Setting
mode.
The
information
that
the
system
expects
next
will
blink
on
the
display.
Setting the Start Time
1,
Press
the
TUNING/TIMER/DIMMER
buttons
to
set
the
hour
that
the
system
will
turn
on.
The
¢
buttonmakes
the
hour
number
decrease,
andthe
»
button
makes
the
hour
number
increase.
2. Press the MEMORY button.
This stores the hour portion of the start-time in memory.
MEMORY.
eS
3.
Press
the
TUNING/TIMER/DIMMER
buttons
to
set
the
minute.
4. Press the MEMORY button.
This stores the minute portion of the start-timer in memory.
Setting the Stop Time
1.
Press
the
TUNING/TIMER/DIMMER
buttons
to
set
the
hour
that
the
system
will
turn
off.
2. Press the MEMORY button.
This stores the hour portion of the stop-time in memory.
3.
Press
the
TUNING/TIMER/DIMMER
buttons
to
set
the
minute.
4. Press the MEMORY button.
This stores the minute portion of the stop time in memory.
Selecting the Source
1.
Press
the
TUNING/TIMER/DIMMER
button
to
select
a
source.
Repeatedly
pressing
the
button
displays
the
sources
in
the
following
order:
Display What it meats
Ho
ee
Re
Plays
from
whichever
source
was
used
just
before
turning
off
the
system
TUNER Plays FM or AM broadcast
TUNER TIMER REC Records FM or AM broadcast
cD Plays a CD
TAPE Plays a tape
--
—-
TIMER
REC
Records
from
whichever
source
was
used
just
before
turning
off
the
system
Note:
*
Ifyou
choose
an
FM
or
AM
radio
station
as
the
source,
select
the
preset
station
by
pressing
the
PRESET
button
on
the
Tuner.
.
2. Press the MEMORY button.
This stores the source to play or record in memory.
Setting the Volume
1. Press the TUNING/TIMER/DIMMER button to selecta volume level.
Repeatedly
pressing
the
>
button
displays
the
volume
levels
in
the
following
order.:
Display What It means
VOL
-- --
Volume
set
to
the
level
used
before
shut
the
power
off.
VOL -~- 0 Volume off
VOL -~ A Volume barely on
VOL
-~
B
Volume
at
about
a
1/4
turn
of
the
volume
knob
VOL
-~
C
Volume
at
about
a
1/3
turn
of
the
volume
knob
21
(No. 20342) 23

JVC ca-mx55mbk Specifications

General

Brand	JVC
Model	ca-mx55mbk
Category	CD Player
Language	English