JVC LT-Z32FX6 Service Manual

(No.YA422)1-9
SECTION 3
DISASSEMBLY
3.1 DISASSEMBLY PROCEDURE
CAUTION AT DISASSEMBLY:
• Be sure to perform the SYSTEM SETTEING, at the end of the procedure.
• Make sure that the power cord is disconnected from the outlet.
• Pay special attention not to break or damage the parts.
• When removing each board, remove the connectors as required. Taking notes of the connecting points (connector numbers)
makes service procedure manageable.
• Make sure that there is no bent or stain on the connectors before inserting, and firmly insert the connectors.
3.1.1 REMOVING THE STAND (Fig.1)
(1) Remove the 2 screws [A].
(2) Remove the STAND COVER.
(3) Remove the 2 screws [B] and 2 screws [C].
(4) Remove the STAND.
3.1.2 REMOVING THE REAR COVER (Fig.1)
• Remove the STAND.
(1) Remove the JACK COVER (L/R).
(2) Remove the 10 screws [D], the 6 screws [E], and the 2
screws [F].
(3) Remove the REAR COVER.
3.1.3 REMOVING THE POWER PWB (Fig.1)
• Remove the STAND.
• Remove the REAR COVER.
(1) Remove the 1 screw [G].
(2) Remove the POWER CORD HOLDER.
(3) Remove the POWER CORD.
(4) Remove the 4 screws [H].
(5) Remove the POWER PWB.
3.1.4 REMOVING THE D-AMP PWB (Fig.1)
• Remove the STAND.
• Remove the REAR COVER.
(1) Remove the 2 screws [J].
(2) Remove the D-AMP PWB.
3.1.5 REMOVING THE ANALOG PWB (Fig.1)
• Remove the STAND.
• Remove the REAR COVER.
• Remove the D-AMP PWB.
(1) Remove the 2 screws [K] and 3 screws [L].
(2) Remove the TERMINAL BASE.
(3) Remove the 1 screw [M].
(4) Remove the TUNER BASE.
(5) Remove the 2 screws [N].
(6) Remove the D-AMP BRACKET.
(7) Remove the 2 screws [P] and 3 screws [Q].
(8) Remove the ANALOG PWB.
3.1.6 REMOVING THE SW PWB (Fig.1)
• Remove the STAND.
• Remove the REAR COVER.
(1) Remove the 3 screws [R].
(2) Remove the CONTROL ASSY with the SW PWB.
(3) Remove the SW PWB.
3.1.7 REMOVING THE DC-DC PWB (Fig.1)
• Remove the STAND.
• Remove the REAR COVER.
(1) Remove the 6 screws [S].
(2) Remove the BACK BRACKET.
(3) Remove the 2 screws [T].
(4) Remove the DC-DC PWB.
3.1.8 REMOVING THE DIGITAL PWB (Fig.1)
• Remove the STAND.
• Remove the REAR COVER.
• Remove the BACK BRACKET.
• Remove the 7 hooks of the SHIELD COVER.
(1) Remove the SHIELD COVER by sliding it in the direction of
the arrow.
(2) Remove the 2 screws [U] and 2 screws [V].
(3) Remove the SHIELD TERMINAL.
(4) Remove the 9 screws [W].
(5) Remove the DIGITAL PWB.
CAUTION :
Make sure to perform the "SYSTEM SETTEING", when
DIGITAL PWB is replaced.

JVC LT-Z32FX6 Specifications

General

Brand	JVC
Model	LT-Z32FX6
Category	LCD TV
Language	English