KTM 250 SX 2019 User Manual

TECHNICAL DATA 21
133
Screw, balancer shaft M8 30 Nm (22.1 lbf ft)
Loctite
®
243™
Screw, cylinder head M8 27 Nm (19.9 lbf ft)
Screw, kick starter M8 25 Nm (18.4 lbf ft)
Loctite
®
2701™
Nut, cylinder base M10 35 Nm (25.8 lbf ft)
Screw, drive chain engine sprocket M10 60 Nm (44.3 lbf ft)
Loctite
®
2701™
Nut, rotor M12x1 60 Nm (44.3 lbf ft)
Gear oil drain plug with magnet M12x1.5 20 Nm (14.8 lbf ft)
Spark plug M14x1.25 25 Nm (18.4 lbf ft)
Nut, inner clutch hub M18x1.5 100 Nm (73.8 lbf ft)
Loctite
®
648™
Nut, primary gear M18LHx1.5 150 Nm (110.6 lbf ft)
Loctite
®
648™
21.2.2 All XC models
Screw, inner membrane sheets EJOTDELTA PT
®
35x25 1 Nm (0.7 lbf ft)
Screw, membrane support plate EJOTDELTA PT
®
30x12 1 Nm (0.7 lbf ft)
Screw, outer membrane sheets EJOTDELTA PT
®
30x6 1 Nm (0.7 lbf ft)
Screw, angle lever, exhaust control M5 6 Nm (4.4 lbf ft)
Loctite
®
243™
Screw, bearing retainer M5 7 Nm (5.2 lbf ft)
Loctite
®
243™
Screw, clutch spring retainer M5 6 Nm (4.4 lbf ft)
Screw, crankshaft position sensor M5 6 Nm (4.4 lbf ft)
Loctite
®
243™
Screw, exhaust control bearing
support
M5 6 Nm (4.4 lbf ft)
Loctite
®
243™
Screw, exhaust control cap M5 5 Nm (3.7 lbf ft)
Screw, exhaust control cover M5 4 Nm (3 lbf ft)
Loctite
®
222™
Screw, locking lever M5 6 Nm (4.4 lbf ft)
Loctite
®
243™
Screw, retaining bracket of exhaust
control
M5 7 Nm (5.2 lbf ft)
Loctite
®
2701™
Bleeder screw, cylinder head M6 10 Nm (7.4 lbf ft)
Nut, water pump impeller M6 6 Nm (4.4 lbf ft)
Loctite
®
243™
Screw, alternator cover M6 8 Nm (5.9 lbf ft)
Screw, clutch slave cylinder M6 10 Nm (7.4 lbf ft)
Screw, control flap, exhaust con-
trol
M6 8 Nm (5.9 lbf ft)
Loctite
®
243™
Screw, engine case M6 10 Nm (7.4 lbf ft)
Screw, exhaust flange M6 8 Nm (5.9 lbf ft)
Screw, gear oil level check M6 10 Nm (7.4 lbf ft)
Screw, intake flange/reed valve
housing
M6 6 Nm (4.4 lbf ft)

KTM 250 SX 2019 Specifications

General

Brand	KTM
Model	250 SX 2019
Category	Motorcycle
Language	English