EasyManuals Logo
Home>KYMCO>Offroad Vehicle>MXU 50 REVERSE

KYMCO MXU 50 REVERSE Service Manual

KYMCO MXU 50 REVERSE
122 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #111 background imageLoading...
Page #111 background image
7. CYLINDER HEAD/CYLINDER/PISTON
7-2
ATV 50
SERVICE INFORMATION
GENERAL INSTRUCTIONS
The cylinder head, cylinder and piston can be serviced with the engine installed in the frame.
Before disassembly, clean the engine to prevent dust from entering the engine.
Remove all gasket material from the mating surfaces.
Do not use a driver to pry between the cylinder and cylinder head, cylinder and crankcase.
Do not damage the cylinder inside and the piston surface.
After disassembly, clean the removed parts before inspection. When assembling, apply the
specified engine oil to movable parts.
SPECIFICATIONS
Unit: mm (in)
Item
Standard Service Limit
Cylinder head warpage
0.1 (0.004)
Piston O.D.(5mm from bottom of piston skirt)
38.97 (1.5588).38.955 (1.5582) 38.9 (1.556)
Cylinder-to- piston clearance
0.03 (0.0012)0.07 (0.0028) 0.1 (0.004)
Piston pin hole I.D.
12.002 (0.48008)12.008 (0.48032) 12.03 (0.4812)
Piston pin O.D.
11.994 (0.47976)12 (0.48) 11.98 (0.4792)
Piston-to-piston pin clearance
0.002 (0.00008)0.014 (0.00056) 0.03 (0.0012)
Piston ring end gap (top/second)
0.1 (0.004)0.25 (0.01) 0.4 (0.016)
Connecting rod small end I.D.
17.005 (0.6802)17.017 (0.68068) 17.03 (0.6812)
Cylinder bore
39 (1.56)39.025 (1.561) 39.05 (1.562)
TORQUE VALUES
Cylinder head bolt 1.6 kgf-m (16 N-m, 11.5 lbf-ft)
Exhaust muffler joint lock nut 1.2 kgf-m (12 N-m, 8.6 lbf-ft)
Exhaust muffler lock bolt 3.3 kgf-m (33 N-m, 23.8 lbf-ft)
Spark plug 1.4 kgf-m (14 N-m, 10.1 lbf-ft)
TROUBLESHOOTING
Compression too low, hard starting
or poor performance at low speed Abnormal noisy piston
Leaking cylinder head gasket Worn cylinder and piston
Loose spark plug Worn piston pin or piston pin hole
Worn, stuck or broken piston and piston rings Worn connecting rod small end bearing
Worn or damaged cylinder and piston
Compression too high, overheating
or knocking Abnormal noisy piston rings
Excessive carbon build-up in cylinder head Worn, stuck or broken piston rings
or on piston head Worn or damaged cylinder

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the KYMCO MXU 50 REVERSE and is the answer not in the manual?

KYMCO MXU 50 REVERSE Specifications

General IconGeneral
BrandKYMCO
ModelMXU 50 REVERSE
CategoryOffroad Vehicle
LanguageEnglish

Related product manuals