Lippert Components Happijac User Manual

16 pages

Other manuals for Lippert Components Happijac

Installation Manual14 pages

Oem Installation Manual22 pages

Questions and Answers:

S
Susan BirdJul 31, 2025
What to do if Lippert Components Industrial Equipment bed(s) will not move either up or down when switch is pressed?
- L
  Luis TaylorAug 1, 2025
  If your Lippert Components Industrial Equipment bed(s) won't move up or down when you press the switch, it could be due to several reasons. First, ensure your trailer batteries are adequately charged or connect to shore power or a generator. If power isn't the issue, the control module or the UP/DOWN switch might be faulty and need replacement. If these steps don't resolve the problem, the motor may be defective, and you should contact LCI Customer Service.
H
Henry CunninghamAug 5, 2025
Why Lippert Components Industrial Equipment bed lowers, but stops part way going up?
- M
  michael52Aug 5, 2025
  If your Lippert Components Industrial Equipment bed lowers, but stops part way going up, it could be due to insufficient power. Make sure your trailer batteries are adequately charged, or connect to shore power or a generator. Alternatively, the motor/brake assembly may be defective; in this case, contact LCI Customer Service.
T
Teresa SchneiderAug 9, 2025
What to do if Lippert Components Industrial Equipment bed travels in only one direction?
- S
  sarah82Aug 10, 2025
  If your Lippert Components Industrial Equipment bed only travels in one direction, it could be caused by a defective limit switch, a faulty control module, or a faulty UP/DOWN switch. Try replacing the switch or module. Another potential cause is a faulty brake. Set the manual brake release lever on the motor to the "OFF" position. If the bed(s) then move, replace the faulty brake.
V
vsmithAug 13, 2025
What to do if Lippert Components Industrial Equipment bed fails to stop at preset stop point when lowered?
- R
  roberthaleAug 13, 2025
  If your Lippert Components Industrial Equipment bed fails to stop at the preset stop point when lowered, the motor brake might not be engaging, or the limit switch may be defective. Contact LCI Customer Service regarding the motor brake, or replace the switch.
P
Patricia DaughertyAug 17, 2025
What to do if Lippert Components Industrial Equipment bed fails to stop at preset stop point when raised?
- M
  Mike MccoyAug 17, 2025
  If your Lippert Components Industrial Equipment bed fails to stop at the preset stop point when raised, the limit switch may be defective or damaged. Replace the switch to resolve this issue.

Lippert Components Happijac Specifications

General

Category	Lifting Systems
Manufacturer	Lippert Components
Brand	Happijac
Mounting Type	Frame-mounted
Lifting Capacity	Varies by model
Operation	Electric

Summary

Safety Information

Safety Warnings and Cautions

Details safety risks associated with WARNING and CAUTION symbols and procedures.

Operating Precautions

General Operating Precautions

Lists essential safety checks and prohibitions during operation.

Operation

Control Switch Operation

Describes how to use the UP/DOWN control switch for the bed lift.

Upper Trolleys Lowering

Troubleshooting

Troubleshooting Common Issues

Lists common problems, their causes, and recommended solutions.

Emergency Manual Operation

Manually Raising the Bed(s)/Sofa or Dinettes

Procedure for manually raising the bed or sofa/dinette.

Manually Lowering the Bed(s)

Related product manuals

Project 2000 12600 Series

Preview: ground control 3.0

ground control 3.0

Preview: Lippert Components Level-Up

Lippert Components Level-Up

Preview: ground control TT

ground control TT

Lippert Components Power Gear

Preview: Lippert Components PSX1

Lippert Components PSX1

Ground Control 2.0

Lippert Components Bed Lift

Lippert Components PSX2

Lippert Components Smart Jack