Manitowoc Flav’R-Pic FRP-250, Flav’R-Pic FRP-250SCI User Manual

Section 2 Installation Instructions
Part Number 020003315 1/11 2-13
BRIXING PROCEDURE
If the merchandiser and splash panel are on the front of
the unit, remove them. Merchandiser removal will give
you access to the syrup and water valves. Splash panel
removal will give you access to the plumbing label
located on the foam front and/or in the Plumbing section
of the Use & Care Manual. This label will be needed to
identify valve and touch pad locations.
Placing a control Board into Brix Mode
Control Board Label
NOTE: See Section 3 for Program Mode Operations.
Mode 2 puts your Flav'R-Pic into brix mode, follow the
steps below to put a board into brix mode.
1. Choose a control board, if brixing drinks for N1 (Nozzle
1) or N3 use the left control board, if brixing drinks for N3
or N6 use the right control board. Beverage dispense
points are designated by a black nozzle.
2. Press the program button and hold for 3 seconds or until
the LED displays 1. Press the program button again until
2 is displayed on the control board LED display.
3. Use a high yield brix cup with multiple ratios for the
procedure, an example is illustrated below. Use of a
funnel between the cup and nozzle will aid in the
capture of the syrup during syrup brixing.
4. Locate the control board that corresponds with the
valve(s) and/or dispense point you want to brix.
NOTE: The buttons for FRP units without flavor shots
are located in the same area, but are hidden.
5. Press the program button and hold for 3 seconds or until
the LED displays 1. Press the program button again until
2 is displayed on the control board LED display.
NOTE: Programming one board at a time will make it
easier for you to identify the corresponding valves and
dispense points. See the Programming section in this
manual for more detail on all programming modes.
6. With a board in mode 2 you can now brix any water
or syrup valve that corresponds to the board. Use
the chart on the left to identify the valves and which
board they correspond to, see the illustration on the
next page for more assistance. Brixing information
can also be found on the right hand side of the
control board cover label. By using this label in
combination with the plumbing label you will be able
to identify each valve, water, and/or syrup
combination.
0
2
Brixing
Info
Left Side
Program
Button
Right Side
Program
Button
Funnel & High Yield Brix Cup
6:1
5.5:1
8.5:1
5:1
WATER
5.5
to 1
8.5
to 1
9
10
8
7
6
5
4
3
2
OZ.
LEFT BOARD RIGHT BOARD
C1 - VA LVE 8 C3 - VALV E 4
C2 - VA LVE 11 C4 - VALV E 1
NC2 - VAL VE 11 NC3 - VALV E 4
S1 - VALVE 8 S9 - VALVE 15
S2 - VALVE 9 S10 - VALVE 3
S3 - VALVE 9 S11 - VALVE 3
S4 - V ALV E 1 4 S12 - V ALVE 7
S5 - V ALV E 1 4 S13 - V ALVE 7
S6 - V ALV E 1 0 S14 - V ALVE 2
S7 - V ALV E 1 0 S15 - V ALVE 2
S8 - V ALV E 1 5 S16 - V ALVE 1
F1 - VA LVE 13 F5 - VALVE 6
F2 - VA LVE 13 F6 - VALVE 6
F3 - VA LVE 12 F7 - VALVE 5
F4 - VA LVE 12 F8 - VALVE 5
C = CARB S = SYRUP F = FLAVOR SHOT
NC = NON-CARB
DISPENSE TYPE &
VALVE NUMBE R
S1
S3
S2
S4
S5
S7
S6
S8
F1
F2
F4
F3
N1
N3
S12
S10
S11
S9
S16 S14
S15
S13
F5
F6
F8
F7
N4
N6
Right
Hidden
Touchpad
Buttons
Left
Hidden
Touchpad
Buttons
FRP-250 WITHOUT FLAVOR SHOTS
Left Carb/
Non-Carb
Right
Carb/Non-
Carb

Manitowoc Flav’R-Pic FRP-250, Flav’R-Pic FRP-250SCI Specifications

General

Brand	Manitowoc
Model	Flav’R-Pic FRP-250, Flav’R-Pic FRP-250SCI
Category	Beverage Dispenser
Language	English