Miele T 7734 User Manual

Adjusting the dryer's
electronics for very soft water
,
In some areas of the UK, water is
extremely soft which can affect the
sensitivity of the control electronics.
If the dryer is installed in an area of
very soft water, you should contact
your local water supplier for
information and advice regarding
water hardness and water
conductivity. If the water
conductivity is less than 150 µS, the
following programmable function will
need to be activated.
Important. This programmable
function should not be activated if,
despite the water being extremely
soft (as would be the case if a water
softener were used), its conductivity
is greater than 150 µS.
Follow the steps (A,B,C ...) to
programme and store in memory.
Before you begin, ensure that:
–
The tumble dryer is switched off.
–
The door is closed.
A Press the Start/Stop button and keep
it pressed in whilst carrying out steps
B-C.
B Switch the dryer on.
Wait until the Start/Stop button lights up
constantly ...
C . . . and then release the Start/Stop
button.
D Press the Low temperature button
ten times.
–
The Low temperature indicator light
will flash on and off slowly once and
then on and off quickly twice.
A number to show which option is
selected will appear in the display
alternating with the letter P.
0 Factory default setting
I Adjusted for very soft water
(the Automatic indicator light will also
flash)
E Pressing the Start/Stop button
switches between the options.
F Switch the dryer off.
The setting you have selected is now
stored in memory. You can change it
again at any time.
To check the setting:
^ Carry out steps A to D.
^ Switch the dryer off after step D.
Programmable functions
57

Miele T 7734 Specifications

General

Brand	Miele
Model	T 7734
Category	Dryer
Language	English

Summary

Warning and Safety Instructions

Correct Application and Usage

Defines the intended domestic use and limitations of the tumble dryer.

Safety with Children

Precautions to ensure children's safety around the appliance.

Technical Safety Precautions

Essential electrical and installation safety measures for the dryer.

Correct Use of Textiles

Lists textiles that must not be dried to prevent fire hazards.

Ventilation and Room Safety

Ensures adequate room ventilation for safe operation and to avoid toxic fumes.

Operating the Tumble Dryer

Control Panel Overview

Notes on Laundry Care

Drying Tips and Recommendations

How to Dry Correctly

Basic Operating Steps

Step-by-step guide for loading, turning on, and operating the dryer.

Laundry Sorting and Loading

Programme Selection Guide

How to choose the appropriate drying programme and drying levels.

Starting and Finishing the Drying Cycle

Steps for starting a programme and removing laundry after completion.

Programme Chart

Cotton Programmes Details

Cleaning and Care

Cleaning the Fluff Filter

Detailed steps for cleaning the fluff filter to ensure efficient operation.

Filter Cleaning Methods

Cleaning Dryer Exterior

Problem Solving Guide

Check and Fault Messages

Troubleshooting common problems and interpreting error messages displayed.

Clean Out Airways Indicator

Troubleshooting the 'Clean out airways' indicator light and related issues.

Drying Process Issues

Resolving problems like long drying times, switching off, or insufficient drying.

Starting and Operational Issues

Troubleshooting why the dryer may fail to start or respond to commands.

Installation and Connection

Installation Site Requirements

Essential conditions for placing the dryer, including worktop clearance.

Levelling the Machine

Ensuring the dryer is perfectly level for safe and proper operation.

Room Ventilation Importance

Crucial need for adequate room ventilation for dryer performance and safety.

Electrical Connection

UK Electrical Safety and Connection

Ensures compliance with UK safety regulations for electrical connection.

Installation - Venting

General Venting Requirements

Key considerations for installing a suitable external venting system for moist air.

Venting Procedure and Materials

Calculating Vent Duct Length and Diameter

Method for calculating the required duct length and ensuring correct diameter.

Appliance Venting Connections

Flexible Ducting Hose Venting

Plastic Piping Venting

Direct Wall Vent Connection

Technical Data

Programmable Functions

Adjusting Residual Moisture for Cottons

Customizing the dryness level for the Cottons programme.

Adjusting Residual Moisture for Minimum Iron

Adjusting Automatic Programme Drying Level

Clean Out Airways Indicator Settings

Customizing when the 'Clean out airways' indicator light is activated.

Adjusting for Very Soft Water

Extending Drying Level Range