EasyManuals Logo
Home>Mitsubishi>Sewing Machine>LS2-210

Mitsubishi LS2-210 User Manual

Mitsubishi LS2-210
22 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #21 background imageLoading...
Page #21 background image
6.
TROUBLESHOOTING
Trouble
Cause
Corrective
Action
Reference
Section
Thread
cannot
be
trim
med.
Knife
engagement
is
improper.
Adjust
the
engagement
amount.
5.1.8
Knife engaging
pressure
is
too
low.
Adjust
the
engaging
pressure.
5.1.8
Damage
and/or
wear
of
cutting
edge
of
movable
knife
(left),
fixed
blade
Change
the
knife
and/or
blade.
Machine
stops
too
early.
Adjust
the
stop
position.
4.2
Machine
stop
position
varies largely.
Check
needle
thread
tension
at
the
time
of
thread
trimming.
5.1.9
Position
of
fixed
blade is
improper.
Adjust
the
position
of
fixed
blade.
5.1.3
Since
the
movable
knife
(left)
is
operated
too
early,
loop
spreading
cannot
be
performed
by
the
knife.
Adjust
the
installation
of
thread
trimmer
cam.
5.1.7
Neeedle
thread
comes
out
of
the
needle
at
the
start
of stitching.
At
the
time
of
thread
trimming,
thread
tension
regulator
discs
do
not
open.
Adjust
the
needle
thread
tension
releasing.
5.1.9
Thread
trimmer
timing is
too
early.
Adjust
the
installation
of
thread
trimmer
cam.
5.1.7
Thread
is
trimmed
by
the
fixed
blade
before
the
cutting
edge
of
movable
knife
(left) engage
with
the
fixed
blade.
Adjust
the
position
of
fixed
blade.
5.1.3
Needle is
too
thick
with
respect
to
the
thread.
Pretension is
too
strong.
Adjust
the
pretension.
5.2
Skip
stitch
at
the
start
of
stitching
Bobbin
thread
becomes
short
due
to
the
Idle
running
of
bobbin
at
the
thread
trimming.
Use a
bobbin
case
with
idle
running
prevention
spring.
5.9
Tension
of
bobbin
thread
Is
too
strong.
The
remaining
length
of
needle
thread
on
the
needle
side
is
too
short
after
thread
trimming.
Adjust
the
tension
of
bobbin
thread.
1.
Adjust
the
pretension.
2.
Check
the
installation
of
thread
trimmer
cam.
3.
Check
the
thread
contact
area.
5.2
5.1.7
Needle
thread
is
too
long
after
thread
trimming.
Pretension
is
too
weak.
Thread
trimmer
timing
is
too
late.
Thread
movement
between
the
hook
and
the
hook
positioner
is
not
smooth.
Adjust
the
pretension.
Adjust
the
installation
of
thread
trimmer
cam.
5.2
5.1.7
20
From the library of: Superior Sewing Machine & Supply LLC

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Mitsubishi LS2-210 and is the answer not in the manual?

Mitsubishi LS2-210 Specifications

General IconGeneral
BrandMitsubishi
ModelLS2-210
CategorySewing Machine
LanguageEnglish

Related product manuals