Home
PolyScience
Chiller
Chiller
PolyScience Chiller User Manual
4
of 1
of 1 rating
43 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
110-240
7
Quick Start
See Installation & Startup for additional information.
1
Connect all process lines
2
Fill reservoir with coolant
3
Connect electrical power
cord to Mains
4
Turn Power Switch /
Circuit Breaker ON
5
Turn Controller ON
6
Add coolant to reservoir
as process lines fill
7
Enter temperature set
point
7
9
Table of Contents
Default Chapter
2
Table of Contents
2
Introduction
4
General Information
5
General Safety Information
5
Safety Recommendations
5
Unpacking Your Chiller
6
Regulatory and Compliance Testing
6
Contents
6
Controls and Components
7
Quick Start
8
Installation and Startup
9
Site Requirements
9
Ambient Temperature and Relative Humidity
9
Location
9
Clearance
9
Electrical Power
9
Optional Signal Inputs/Outputs
10
External Ambient Tracking Temperature Probe
10
RS232 / RS485 Serial Output
10
Remote I/O Port
10
Plumbing
10
Process Piping
10
Reservoir Drain
10
External Water Filter
10
Closed Sytem or Cooling Coil Setup
11
Open Bath System Setup
11
Startup
11
Process Coolant
11
Electrical Power
12
Starting Process Fluid Flow
12
Normal Operation
14
Selecting the Temperature Unit
14
Displaying and Adjusting the Set Point
14
Displaying and Adjusting the Ambient Tracking Offset
14
Displaying and Adjusting the Remote Control Temperature
15
Selecting the Pressure / Flow Rate Display and Units
15
Selecting the Internal / External Temperature Display
15
Setting Operational Parameters
16
High Temperature Limit (HL)
17
Low Temperature Limit (LL)
17
High Ambient Temperature Limit (HA)
17
Maximum Fluid Pressure (FP)
17
Minimum Flow Rate (FL)
18
Maximum External / Internal Temperature Differential (Sd)
18
Auto-Refrigeration Temperature (AF)
19
Remote Probe (Rp)
19
Internal Calibration Offset (C1)
20
External Calibration Offset (C2)
20
Baud Rate (PC)
21
Display, Alarm and Error Messages
21
Adjusting the High Pressure Bypass Setting
24
Enabling / Disabling the Local Lockout
24
Routine Maintenance and Troubleshooting
25
Routine Maintenance
25
Standard Magnetic Drive Centrifugal Pump
25
Condenser, Air Vents and Reusable Filter
25
Fluid Filter
25
Fluid Level
25
Temperature Calibration
25
Troubleshooting
26
Diagnostic Mode
27
Technical Information
28
General Specifications (All Chillers)
28
Pump Performance
28
Performance Specifications - 60Hz Chillers
29
1/4-HP, 1/3-HP and 1/2-HP Chillers
29
3/4-HP and 1-HP Chillers
31
Performance Specifications - 50Hz Chillers
33
1/4-HP, 1/3-HP and 1/2-HP Chillers
33
3/4-HP and 1-HP Chillers
35
Diagrams and Schematics
37
Electrical Wiring Diagram
37
Flow Schematic
38
Replacement Parts
39
RS232 Communications
41
Equipment Disposal (WEEE Directive)
42
Service and Technical Support
42
Warranty
43
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the PolyScience Chiller and is the answer not in the manual?
Ask a question
PolyScience Chiller Specifications
General
Brand
PolyScience
Model
Chiller
Category
Chiller
Language
English
Related product manuals
Refrigerated Recirculating Chillers
32 pages
PolyScience LS Series
22 pages
To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...
Need help?
General
