4. If you have another VCR connected
to the TV, press MENU•PROG to
select the VCR 2 CHAN function.
5. Enter the channel number you want
to program by pressing two digit
buttons on the remote control. (This
is the channel number to which the
TV will tune automatically when you
later press the VCR2•LD button on
the remote.) See the notes below if
you are unsure about which channel
number to enter.
6. Press the + button to program the
channel number you selected into the
VCR 2 CHAN function memory.
Note: Pressing the – button here will
turn off this feature and display
VCR 2 CHAN: OFF again.
20
1. Repeatedly press MENU•PROG to
select SETUP MENU, and then press
+ or – to display the setup functions.
Repeatedly press MENU•PROG to
select the VCR 1 CHAN function.
2. Enter the channel number you want to
program by pressing two digit buttons
on the remote control. (The channel
number you enter is the channel to
which the TV will tune automatically
when you later press the VCR1 button
on the remote.)
3. Press the + button to program the
channel number you selected into the
TV’s memory.
Note: Pressing the – button here will turn
off this feature and display
VCR 1 CHAN: OFF again.
Setting Up VCR Channels
The VCR 1 CHAN function lets you
program to which channel the TV
will automatically tune when you
press the VCR1 button on the remote.
This is handy if you connect a VCR
to your TV. You will no longer have
to remember to which input jacks the
VCR is connected because the TV
will remember for you.
For example, if you connect a VCR’s
AUDIO/VIDEO OUT jacks to the
TV’s INPUT 1 jacks (as shown on
page 28), you will no longer have to
remember to select channel 91 on the
TV to see what the VCR is playing.
By entering channel 91 next to the
VCR 1 CHAN function, the TV will
automatically tune to channel 91
each time you press the VCR1 button
on the remote.
This function is especially
convenient if you have a compatible
VCR that can be operated by the
VCR1 button on the remote. Pressing
VCR1 will then not only turn on the
VCR but also automatically tune the
TV to the proper channel for viewing
the picture from the VCR. You can
program most brands of remote-
controllable VCRs to respond to the
VCR1 button as described on
page 31.
The VCR 2 CHAN function works
the same way. It lets you program to
which channel the TV will
automatically tune when you press
the VCR2•LD button on the remote.
You can program most brands of
remote-controllable VCRs to respond
to the VCR2•LD button as described
on page 31. Pressing the VCR2•LD
button will then not only turn on the
VCR but also automatically tune the
TV to the proper channel for viewing
the picture from the VCR.
Notes about Entering Channel Number:
• Enter channel 91 if VCR is connected to the TV’s audio and video INPUT 1 jacks.
• Enter channel 92 if VCR is connected to the TV’s audio and video INPUT 2 jacks.
• Enter channel 90 if you have a Super-VHS VCR that is connected to the TV’s
S-VIDEO connector and INPUT 1 audio jacks (labeled L and R/MONO).
• Enter channel 03 (or 04) if you did not use any audio/video cables and connected the
VCR to the TV’s round antenna jack labeled CABLE/ANTENNA. Enter the same
channel number (03 or 04) as the position of the VCR’s CH3/CH4 switch. This is
the channel to which you must tune your TV for viewing signals from your VCR.
• Refer to pages 28-29 if you want to review details about connecting your VCR to
your TV.
Setting Up VCR Channels (with or without remote)
Autoprogram
Chan Mem: Stored
Cable/Air: AIr
VCR1 Chan: 91
VCR 2 Chan: 92
7:57 PM Input 1 91
Autoprogram
Chan Mem: Stored
Cable/Air: AIr
VCR1 Chan: 91
VCR 2 Chan: Off
8:04 PM Input 2 92
Autoprogram
Chan Mem: Stored
Cable/Air: AIr
VCR1 Chan: 91
VCR 2 Chan: Off
Mute
Video Menu
Audio Menu
Setup Menu
Chan Ctrl: Normal
Autoprogram
Chan Mem: Stored
Cable/Air: AIr
VCR1 Chan: Off
7:57 PM 12
7:57 PM Input 1 91
Chan Ctrl: Normal
Autoprogram
Chan Mem: Stored
Cable/Air: AIr
VCR1 Chan: Off
Chan Ctrl: Normal
Autoprogram
Chan Mem: Stored
Cable/Air: AIr
VCR1 Chan: 91
To Next Page
Loading...
Need help?
General
