EasyManuals Logo
Home>Reolink>DVR>RLN8-410

Reolink RLN8-410 User Manual

Reolink RLN8-410
65 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #64 background imageLoading...
Page #64 background image
Reolink PoE NVR
User Manual
52
Cause 1. The power adapter issues.
Solution:
Check the status LED on the power adapter of the NVR. If the LED isn't on, please
plug the power adapter into another socket as well as change another working
power adapter (48V) for a try. If the LED is on, please check the HDD issue below.
Cause 2. The HDD issues.
Solution:
Please unplug the HDD and check if the NVR will power on without HDD.
Cause 3. The voltage is not sufficient.
Solution:
Unplug all cameras. If the NVR power LED is on, please re-plug the camera in
sequence to see how many cameras the NVR can provide power normally before
the issue started.
10. Camera randomly disconnects from the NVR.
If you found that the cameras disconnect and show video loss/connection failed
randomly on your NVR monitor, or the camera loses recordings randomly, here are
some possible causes and solutions for your reference.
Cause 1. Poor connection between camera and NVR.
Solution:
(1) If you connect your camera to the NVR via the Ethernet cable directly, please
make sure that the length between them is less than 260 feet.
(2) Please change with another short cable and plug it into another PoE port. If
possible, please connect only one camera to the NVR to test whether the issue still
exists.
(3) Please lower the bitrate of the camera and check if the issue can be fixed.
If you connect the camera to the router by PoE switch/ injector and add your
camera to the NVR, the issue may cause by the poor network of the router.
(1) Please reboot the router and camera to try again.
(2) If you have connected several devices to the router, please only connect the
camera to the router to test the issue.
(3) Please also lower the bitrate of the camera and check if the issue can be fixed.
(4) Please connect the camera directly to the PoE port of the NVR to check
whether the issue still exists.
Cause 2. Software issue.
Solution:
Please check the firmware version of the camera and NVR, keep both of them
updated.

Table of Contents

Other manuals for Reolink RLN8-410

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Reolink RLN8-410 and is the answer not in the manual?

Reolink RLN8-410 Specifications

General IconGeneral
Video codecsH.264
Display modesLive view
Number of users20 user(s)
Maximum resolution3840 x 2160 pixels
Video input channels8 channels
Supported resolutions3840x2160, 1920x1080, 1440x900, 1280x1024, 1280x800, 1280x720, 1024x768
On/off switchYes
Product colorBlack
Audio RCA outputs1
Networking standardsIEEE 802.3af, IEEE 802.3at
USB 2.0 ports quantity2
Ethernet LAN data rates10, 100, 1000 Mbit/s
Ethernet LAN (RJ-45) ports9
Supported network protocolsHTTP, TCP/IP, UDP, DHCP, P2P, UPNP, RTSP, SMTP, SSL/TLS, DNS, DDNS, NTP, FTP
Power over Ethernet (PoE) ports quantity8
Wi-FiNo
HDD capacity2000 GB
HDD interfaceSATA, SATA II, SATA III
Maximum storage capacity8 TB
Output current2 A
Output voltage48 V
Power consumption (max)25 W
Operating temperature (T-T)-10 - 45 °C
Operating relative humidity (H-H)10 - 90 %
Weight and Dimensions IconWeight and Dimensions
Depth230 mm
Width260 mm
Height41 mm
Weight1200 g

Related product manuals