www.scheppach.com
32
|
GB
9.2 Thicknessing
m IMPORTANT!: Pull out the power plug before
performing any maintenance, cleaning and adjusting
work.
9.2.1 Adjustment (g. 22)
• Place the crank handle (12) on the spindle and turn
it to adjust the thicknessing table (21) to the required
height. The set angle can be read o the scale (G).
• It is important to adjust the height of the planing ta-
ble (21) from bottom to top, i.e. crank the table fur-
ther down (approx. 5 mm) than the desired height.
Then crank the table (21) upwards to the desired
height.
9.2.2 Thicknessing mode (g. 22)
Attention! Watch out the right mounting of the chip ex-
tractor (point 8.7)
• Plug in the machines power cord. Press the green
button “I” to start the plane (2).
• Place a workpiece on the thicknessing table (21).
Guide the workpiece towards the feed table (14).
• When you have nished work, switch o the ma-
chine. To do this, press the red button “0”. Then dis-
connect the machine from the mains supply.
• Remove the chips and dust from the thicknessing
table (21) and knife block after the machine has
reached a complete standstill.
10. Electrical connection
The electrical motor installed is connected and
ready for operation. The connection complies with
the applicable VDE and DIN provisions. The cus-
tomer‘s mains connection as well as the exten-
sion cable used must also comply with these reg-
ulations.
Important information
In the event of an overloading the motor will switch it-
self o. After a cool-down period (time varies) the mo-
tor can be switched back on again.
Damaged electrical connection cable.
The insulation on electrical connection cables is often
damaged.
9.1 Surfacing
m IMPORTANT!: Pull out the power plug before per-
forming any maintenance, cleaning and adjusting work.
9.1.1 Adjustment (g. 7/8)
• Turn the adjustment knob for cutting depth (13) to
set the height of the feed table. The set cutting depth
can be read o the scale (H).
• Loosen the parallel stop (8) with the clamping crew
(8a). Adjust the desired angle. The adjusted angle
can be read o the scale (I). Fix the parallel stop (8)
with the clamping screw (8a) after adjustment.
9.1.2 Surface planing mode (g. 20 + 21)
Attention! Watch out the right mounting of the
chip extractor (point 8.5)
• (Narrow workpieces see g. 21) Open the knurled
srcew (10) and slide the planer blade cover (9) as far
as the width of the workpiece requires. Then tighten
the knurled srcew (10) again.
• (Width, at workpieces see g. 20) Open the star
knob nut (4) and set the planer blade cover com-
pletely. (9) is just as high as the workpiece is thick.
The planer blade cover (9) covers the entire blade
roller! Tighten the star knob nut (4) again.
• Plug in the machines power cord ( Press the green
button “I” to start the plane (1).
• Place the workpiece you wish to plane on the feed
table (14). Slide the workpiece as far as possible
with the push stick (16) forwards towards the planing
table (7) over the knives (25).
• When you have nished work, switch o the ma-
chine. To do this, press the red button “0”. Then dis-
connect the machine from the mains supply.
• Remove the chips and dust from the feed table (14),
planing table (7) and knife block after the machine
has reached a complete standstill.
• Move the planing knife cover (9) back into position
and cover the entire length of the planing knife.
To Next Page
Loading...
Need help?
General
