Scheppach HMS860 User Manual

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
GB
|
27
without hindrance due to their own weight;
• Planing blades (Fig. 17 - pos. 25)
for signs of damage and to ensure they are posi-
tioned correctly.
The machine may only be used if all these condi-
tions are satised.
Use only well sharpened and maintained blades.
Use only blades that are designed for the machine.
Use pusher wood or sticks which are in perfect con-
dition for machining short workpieces.
Connect the machine to a dust and chip extractor.
Check that the stop is secure before starting the
machining work.
Ensure that you can maintain your balance at all
times. Stand to the side of the machine.
Whilst the machine is running keep your hands at
a safe distance from the cutting block and from the
point at which the chips are discharged.
Do not start the planing work until the cutting block
has reached the required speed.
Also ensure that the workpiece does not contain any
cables, wires, cords or the like. Do not machine any
wood which has lots of knots or knot holes.
Secure long workpieces to prevent them tipping over
at the end of the planing process. Use roller stands,
for example, or similar devices for this purpose.
Removing sawdust and chippings from the machine
when running is strictly prohibited.
Switch o󰀨 the machine immediately it is jams. Pull out
the mains plug and remove the jammed workpiece.
Set the smallest cutting size after use to prevent the
risk of injury.
m CAUTION!
The machine must be secured to the oor / coun-
tertop using suitable screws / screw clamps since
otherwise there is a risk that it will tip over.
• Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
• m WARNING! Before cleaning~, adjustment~,
maintenance~ or repair work, disconnect the pow-
er cord from the main power supply!
• Check at regular intervals that the knife (25) is
rmly attached in the knife block.
• The knives (25) must not project more than a max-
spindle.
8.5 Chip extraction (Fig. 10)
• To mount the extension of the chip extraction (5a),
open the Phillips screw on the extension. Fit both
parts (5, 5a) together and retighten the Phillips
screw.
8.6 Chip extractor - surface planing (Fig. 11+12)
• Set the planing knife cover cpl. (9) in the upperst
position.
• Use the crank handle (12) to place the Thickness-
ing table (21) in the lowest position.
• Take the chip extractor (5) and hold the switching
pins (3) beside. Place the chip extractor (5) at a
slightly slanting angle on the machine and push it
backwards. For this you need to hold the switching
pins (3) outwards.
• Now lock the chip extractor (5) with the switching
pins in the table. Attention! The machine won´t start
if the switching pins are incorrectly plugged in.
• Now you can fold the planing knife cover cpl. (9)
down again.
8.7 Chip extractor - thickness planing (Fig.
13+14)
• The parallel stop (8) needs to be removed for thick-
ness planing. Follow point 8.3 in reverse order.
• Hold the switching pins (3) outside and set the chip
extractor (5) on top of the machine.
• Now lock the chip extractor (5) with the switching
pins in the table. Attention! The machine won´t start
if the switching pins (3) are incorrectly plugged in.
9. Installation
m IMPORTANT!
You must fully assemble the appliance before
using it for the rst time!
Before each use, check the following:
• Proper function of the on and o󰀨 button, incl. the
emergency switch (if available).
• Locked disconnected protective equipment
(Abb 1a - pos. 3)
by gradual opening of every separating protective
equipment to be able to turn the machine o󰀨 and
checking that the machine cannot be turned on
whenever the protective equipment is open
• Brake
Switch on the machine at the start of work and allow
the machine to reach speed. Now switch the ma-
chine o󰀨 again. The engine must come to a standstill
within 10 seconds. Otherwise, there is a defect.
• Anti-kick claws (Fig. 9 - pos. 20)
at least once per shift by a visual inspection to estab-
lish that they are in good working order, for example,
that the contact surface has not been damaged by
impacts and that the anti-kick claws (20) fall back

Scheppach HMS860 Specifications

General

Power	1500 W
Idle speed	9000 RPM
Product color	Black, Blue, Grey
Dust extraction	Yes
AC input voltage	230 - 240 V
Housing material	-
AC input frequency	50 Hz
Planning width (max)	204 mm

Weight and Dimensions

Depth	805 mm
Width	445 mm
Height	430 mm
Weight	29500 g
Thicknessing table dimensions (W x D)	270 x 251 mm