31 | GB
www.scheppach.com service@scheppach.com +(49)-08223-4002-99 +(49)-08223-4002-58 www.scheppach.com service@scheppach.com +(49)-08223-4002-99 +(49)-08223-4002-58
• Change the oil at the end of every season. To do
so, remove the used engine oil from a warm engine
and rell with fresh oil.
• Remove the spark plug from the cylinder head. Fill
the cylinder with approx. 20 ml of oil from an oil can.
Slowly pull back the starter handle, which will bathe
the cylinder wall with oil. Screw the spark plug back
in.
• Clean the cooling ns of the cylinder and the hous-
ing.
• Be sure to clean the entire machine to protect the
paint.
• Store the machine in a well-ventilated place.
Preparing the mower for transportation (Fig. 22)
• Empty the petrol tank.
• Always let the engine run until it has used up the
remainder of petrol in the tank.
• Empty the engine oil from the warm engine.
• Remove the spark plug boot from the spark plug.
• Clean the cooling ns of the cylinder and the hous-
ing.
• Remove the start tension cable (17) from the hook.
Loosen the quick-release lever (5) and fold the up-
per push bar down. Make sure the cables are not
bent during this process.
• Wedge a few layers of corrugated cardboard be-
tween the upper and lower push bars and the en-
gine in order to prevent any chang.
11. Disposal and recycling
Transport package disposal
The package protects the appliance against damage
during transport. Packing materials are usually cho-
sen depending on their environmental friendliness
and disposal method and can therefore be recycled.
Returning the package to material circulation saves
raw materials and reduces waste disposal costs.
Parts of packages (e.g. foils, styropor®) can be dan-
gerous to children. Risk of suffocation! Keep parts of
packages away from children and dispose them as
soon as possible.
The unit and its accessories are made of various
types of material, such as metal and plastic. Defec-
tive components must be disposed of as special
waste. Ask your dealer or your local council.
12. Troubleshooting
Troubleshooting
The table shows potential failures, their possible
cause and removal options. However, if you are un-
able to remove the problem, contact a professional
to assist you.
m CAUTION!
Always switch off the engine and pull the ignition ca-
ble before starting any inspection or adjustment work.
m CAUTION!
If, after making an adjustment or repair to the engine,
you let it run for a few minutes, remember that the ex-
haust and other parts will get hot. Thus, do not touch
parts that emanate heat, as these may burn you.
Important hint in case of sending the equipment
to a service station:
Due to security reasons please see to it that the
equipment is sent back free of oil and gas!
Fault Possible cause Remedy
Loud while running,
machine vibrates heavily
• Screws are loose
• Blade fasteners are loose
• Blade is unbalanced
• Check screws
• Check blade fasteners
• Replace blade
Engine does not start
• Brake lever not pressed
• Speed lever in wrong position
• Spark plug is defective
• Fuel tank is empty
• Contaminated fuel
• Cold environment
• Engine faulty
• Press brake lever
• Check setting
• Replace spark plug
• Rell with fuel
• Empty fuel tank and ll with clean fuel
• Push the primer button (if present)
• Contact authorised customer service
Engine runs unsteadily
• Air lter is soiled
• Spark plug is soiled
• Clean the air lter
• Clean the spark plug
Uneven mowing results
• Blade is blunt
• Cutting height is too low
• Sharpen the blade
• Set correct height
Unsatisfactory bagging of
the grass
• Cutting height is too low
• Blade is worn
• Basket is clogged
• Set correct height
• Replace the blade
• Empty the basket
To Next Page
Loading...
Need help?
General
