Siemens SINUMERIK 810M User Manual

3 Operating Sequences 09.91
3.1.15 Data input/data output
Notes:
When inputting from punched tape, the input data are checked for simple errors.
All characters in punched tape code have a common identification character:
• in ISO code there is always an even hole count
• in EIA code there is always an odd hole count
The control automatically identifies the correct code when reading the first ”%” (ISO) or ”EOR” (EIA)!
The criterion ”Odd hole count” or ”Even hole count” is used for character parity checking from the second character in
the program onwards.
As a further check, if a program already in the program memory is read in again, a complete program comparison is
carried out.
When an error is recognized, reading in is stopped and the error displayed on the CRT.
3.1.15.3 Data output
In any of the operation modes:
PRESET / JOG / AUTOMATIC /
INC 1 .... INC 10000 / REFPOINT,
operate the ”DATA IN-OUT” softkey and subsequently
”DATA OUTPUT”.
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
DATA
IN-OUT
DATA
OUTPUT
Sequence of operation
This input form, with the input field
identified in inverse video, appears.
((Bild 810M/42 einmontieren))
PART
PROGRAM
Using the softkey, now select, for example, the ”PART
PROGRAM” function.
Now enter:
”1” ( for output via Interface 1 ) or
”2” ( for output via Interface 2 )
and store it using the input key.
or
1
a a a a a a a a a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a a a a a a a a a
F
2
a a a a a a a a a a
a
a a a a a a a a
a
a
a a a a a a a a
a
a
a a a a a a a a
a
a
a a a a a a a a
a
a
a a a a a a a a
a
a
a a a a a a a a
a
a
a a a a a a a a
a
a
a a a a a a a a
a
a a a a a a a a a a
D
3-84 © Siemens AG 1990 All Rights Reserved 6ZB5 410-0EQ02
SINUMERIK 810M, GA3 (BN)

Siemens SINUMERIK 810M Specifications

General

Brand	Siemens
Model	SINUMERIK 810M
Category	Control Systems
Language	English