Tecsun PL-365 User Manual

TECSUN RADIOS AUSTRALIA
24/9 Powells Road, Brookvale, NSW 2100 Australia
Ph: +61 2 9939 4377
Email: info@tecsunradios.com.au
www.tecsunradios.com.au
SLEEP FUNCTION
11
Delete all memories
Method 2: SEMI AUTO-DELETE MEMORY
Press the [VF/VM] button to enter the memory mode,
then press & hold the [VF/VM] button to activate the
memory auto-browse function. During the browsing
process unwanted stations can be deleted by pressing
the [DEL.] button. Press the [VF/VM] button again to
stop browsing.
SLEEP
10
Method 2: MANUALLY STORING STATION
1. Tune to your desired station, press the [MEM.] button
once and notice the PRESET number flashing in the
upper right corner of the display.
2. The station is automatically stored after 3 seconds;
press the [MEM.] button to confirm immediately. If you
prefer to store the station at a different memory position,
rotate the [TUNING] knob to the position of your choice
and press the [MEM.] button to confirm.
Method 3: SEMI-AUTO STATION STORAGE
1. Short press the [VF/VM] button to enter frequency
mode.
2. Long press [VF/VM] button to activate the Auto-browse
function.
3.
During the browsing process, press the [MEM.]
button to store stations into the next available
memory position. The browsing process continues
until you press the [VF/VM] again.
DELETE MEMORY
Method 1: DELETE SINGLE MEMORY MANUALLY
1. Turn the radio on and press the [VF/VM] button until
"Preset" and the memory position appears in the upper
right corner of the display.
2. Rotate the [TUNING] knob to select the stored station
you wish to delete.
3. Press & hold the [DEL.] button until " " flashes on
the display, press again to confirm.
Note: If " " is flashing more than 3 seconds without
confirmation, it will exit the delete function automatically.
1. In POWER OFF mode, press &
hold the [POWER] button untill
the sleep timer symbol “ ”
flashes on the display.
2. Rotate the [TUNING] knob
immediately to select a sleep
timer from 1 - 120 minutes or
select “ ” for POWER ON
mode (the radio will be turned
on after 1 second).
Note: The default setting of the sleep timer is “ ”.
SLEEP
Sleep time range
SLEEP
flashing
flashing
DELETE ALL MEMORY
Press the [VF/VM] button to
enter the memory mode, then
press & hold the [DEL.] button
until " " appears on the
display, press the [DEL.] button
again to confirm.
Note: If the [DEL.] button is not pressed within 2 seconds
to confirm, the delete function is automatically exited.
Method 3:

Tecsun PL-365 Specifications

Frequency Range

FM frequency range	87~108 MHz
Japan FM frequency range	76~108 MHz
EU, USA FM frequency range	87.5~108 MHz
MW frequency range	522~1620 (150~1620) kHz
USA MW frequency range	520~1710 kHz
SW frequency range	1711~29999 kHz

Sensitivity

FM sensitivity (S/N=30dB)	Less than 3μV
MW sensitivity (S/N=26dB)	Less than 1mV/m
LW sensitivity (S/N=26dB)	Less than 10mV/m
SW sensitivity (S/N=26dB)	Less than 30μV
SSB sensitivity (S/N=10dB)	Less than 3μV

Selectivity and Stereo Crosstalk

FM selectivity	＞60 dB
MW selectivity	＞60 dB
LW selectivity	＞60 dB
SW selectivity	＞60 dB
FM Stereo crosstalk	Less than 25 dB

Power and Output

Memory capacity	550
Output power	350 mW
Battery type	UM3 or AA X 3
USB power	5V DC

Speaker and Connectivity

Speaker specifications	Φ40mm, 500mW/16 Ohm
Earphone jack specifications	Φ3.5mm, 8~32 Ohm, Stereo type

Weight and Dimensions

Dimensions	Approx. 53(W) X 159(H) X 26(D) mm
Weight	128g (Batteries not included)