Trane IntelliPak CGAF Series User Manual

41
System Testing & Troubleshooting
OR
The followin
g
screen will display on 40 to 60 Ton units.
Used on Units:
40 to 60 Ton
Possible Values:
On, Off
1. Press the + or - key until the proper value is displayed.
2. Press the ENTER key to confirm this choice.
3. Press the NEXT key to advance the cursor to the "K12"
4. Press the + or - key until the proper value is displayed.
5. Press the ENTER key to confirm this choice.
6. Press the NEXT key to advance the cursor to the "K3"
7. Press the + or - key until the proper value is displayed.
8. Press the ENTER key to confirm this choice.
9. Press the NEXT key to advance the cursor to the "K4"
10. Press the + or - key until the proper value is displayed.
11. Press the ENTER key to confirm this choice.
12. Press the NEXT key until the followin
g
screen is displayed.
Used on Units:
All Units
Possible Values:
On, Off, Auto
1. Press the + or - key until the proper value is displayed.
2. Press the ENTER key to confirm this choice.
3. Press the NEXT key to advance the cursor to the "1B"
4. Press the + or - key until the proper value is displayed.
5. Press the ENTER key to confirm this choice.
6. Press the NEXT key until the followin
g
screen is displayed.
7. Press the + or - key until the proper value is displayed.
8. Press the ENTER key to confirm this choice.
9. Press the NEXT key to advance the cursor to the "2B"
The followin
g
screen will display on 40 to 60 Ton units.
Used on Units:
40 to 60 Ton
Possible Values:
On, Off, Auto
1. Press the + or - key until the proper value is displayed.
2. Press the ENTER key to confirm this choice.
3. Press the NEXT key to advance the cursor to the "1B"
4. Press the + or - key until the proper value is displayed.
5. Press the ENTER key to confirm this choice.
6. Press the NEXT key to advance the cursor to the "2A"
7. Press the + or - key until the proper value is displayed.
8. Press the ENTER key to confirm this choice.
9. Press the NEXT key to advance the cursor to the "2B"
Used on Units:
All Units
Possible Values:
Auto, 0 to 100%
Note: This is the low ambient damper position
1. Press the + or - key until the proper value is displayed.
2. Press the ENTER key to confirm this choice.
Circuit 2 is used for 40 through 60 Ton units only.
3. Press the NEXT key to advance the cursor to the "Ckt 2"
4. Press the + or - key until the proper value is displayed.
5. Press the ENTER key to confirm this choice.
6. Press the NEXT key until the followin
g
screen is displayed.
Used on Units:
All Brazed Plate Units
Possible Values:
On, Off
1. Press the + or - key until the proper value is displayed.
2. Press the ENTER key to confirm this choice.
3. Press the NEXT key until the followin
g
screen is displayed.
1. Press the + or - key until the proper value is displayed.
2. Press the ENTER key to confirm this choice.
3. Press the NEXT key until the followin
g
screen is displayed.
Compressor Relays
K11 OFF K12 OFF K3 OFF K4 OFF
Condenser Fan Outputs
2A OFF 2B OFF 2C OFF
Condenser Fan Speed
Ckt1 0% Ckt2 0%
CGM Alarm Output: OFF
Condenser Fan Outputs
1A OFF 1B OFF 1C OFF
MCM Heater Tape Relay K13: OFF
Relay ON: Heat Off, Relay OFF: Heat On

Trane IntelliPak CGAF Series Specifications

General

Brand	Trane
Model	IntelliPak CGAF Series
Category	Air Conditioner
Language	English