Wilo Easy Control MS-L 1x4kW User Manual

26 WILO SE 08/2013 Ed.04 DIN A4
English INTRODUCTION
1. Introduction
1.1. About this document
The language of the original operating manual is
German. All other languages of these instructions
are translations of the original operating instruc-
tions.
This manual is divided into individual sections,
which are listed in the table of contents. Each
section has a heading which clearly describes its
content.
A copy of the EC declaration of conformity is a
component of these operating instructions.
Ifatechnicalmodicationismadeonthedesigns
named there without our agreement, this decla-
ration loses its validity.
1.2. Personnel qualications
All personnel who work on or with the switchgear
mustbequaliedforsuchwork;electricalwork,
forexample,mayonlybecarriedoutbyaqualied
electrician. All personnel must be of legal age.
Operating and maintenance personnel must also
observe national accident prevention regulations.
It must be ensured that personnel has read and
understood the instructions in this operation and
maintenance manual; if necessary, this manual
must be ordered from the manufacturer in the
required language.
This switchgear is not intended for use by persons
(including children) with reduced physical, senso-
ryormentalcapabilities,orlackofexperienceand
knowledge, unless they have been given supervi-
sion or instruction concerning use of the switch-
gear by a person responsible for their safety.
Children should be supervised to ensure that they
do not play with the switchgear.
1.3. Abbreviations
• p.t.o. = please turn over
• re. = regarding
• approx.=approximately
• i.e. = that means
• incl. = including
• min. = minimum
• max.=maximum
• etc. = and so on
• s.a. = see also
• e.g.=forexample
1.4. Copyright
This operation and maintenance manual has been
copyrighted by the manufacturer. The operation
and maintenance manual is intended for use by
installation, operating and maintenance person-
nel. It contains regulations and drawings which
may not be reproduced or distributed, either
completely or in part, or used for any competitive
purposewithouttheexpressedconsentofthe
manufacturer. Illustrations may differ from the
originalandserveonlyasexampleillustrationsof
switchgears.
1.5. Rights of modication
The manufacturer reserves the right to make
technicalmodicationstosystemsorcompo-
nents. This operation and maintenance manual
refers to the switchgear indicated on the title
page.
1.6. Warranty
This section contains the general information on
the warranty. Contractual agreements have the
highest priority and are not superseded by the
information in this section.
The manufacturer is obliged to correct any
defects found in the switchgears it sells, provid-
ed that the following requirements have been
fullled:
1.6.1. General
• The defects are caused by the materials used
or the way the product was manufactured or
designed.
• The defects were reported in writing to the man-
ufacturer within the agreed warranty period.
• The switchgear was used only as intended.
1.6.2. Warranty period
If no other provisions have been made, the war-
rantyperiodappliestotherst24monthsafter
commissioningortoamax.periodof30months
after the delivery date. Other agreements must be
madeinwritingintheorderconrmation.These
remain valid at least until the agreed warranty
periodoftheswitchgearhasexpired.
1.6.3. Spare parts, attachments and modications
Only genuine spare parts from the manufacturer
may be used for repairs, replacements, attach-
mentsandmodications.Unauthorizedadd-ons
andmodicationsortheuseofnon-originalspare
parts can seriously damage the switchgear and/or
injure personnel.
1.6.4. Maintenance
The prescribed maintenance and inspection
work should be carried out regularly. This work
mayonlybecarriedoutbyqualied,trainedand
authorized personnel.
1.6.5. Damage to the product
Damage and faults that endanger safety must
be eliminated immediately by trained personnel.
The switchgear may only be operated if it is in
proper working order. During the agreed warranty
period, the switchgear may only be repaired by
the manufacturer or an authorized service center.
The manufacturer reserves the right to ask the
operator to return the damaged switchgear to the
factory for inspection.
1.6.6. Exclusion from liability
No liability will be assumed for damage to the
switchgear if any of the following items apply:

Wilo Easy Control MS-L 1x4kW Specifications

General

Brand	Wilo
Model	Easy Control MS-L 1x4kW
Category	Control Unit
Language	English