EasyManuals Logo
Home>Cisco>Network Router>12000 - Series Chassis Modular Expansion Base

Cisco 12000 - Series Chassis Modular Expansion Base User Manual

Cisco 12000 - Series Chassis Modular Expansion Base
132 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #89 background imageLoading...
Page #89 background image
2-47
Cisco 12000 Series Router SIP and SPA Hardware Installation Guide
Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007
Chapter 2 Overview: Cisco 12000 Series Router Shared Port Adapters
2-Port, 4-Port, and 8-Port OC-3c/STM-1 and OC-12c/STM-4 POS SPA, 4-Port OC-3c/STM-1 POS SPA, and 8-Port
The SFP optical transceiver modules used with the 2-Port, 4-Port, and 8-Port OC-3c/STM-1 and
OC-12c/STM-4 POS SPA configured for OC-3 and the 4-Port and 8-Port OC-3c/STM-1 POS SPA
provide the following optical fiber options:
• Multimode—155.52-Mbps, OC-3 optical fiber (SONET STS-3c or SDH STM-1)
Use a multimode optical fiber that has a core/cladding diameter of 62.5/125 microns.
• Single-mode—155.52-Mbps, OC-3 optical fiber (SONET STS-3c or SDH STM-1)
Use a single-mode optical fiber that has a modal-field diameter of 8.7 ± 0.5 microns. (Nominal
diameter is approximately 10/125 microns.)
The SFP optical transceiver modules used with the 2-Port, 4-Port, and 8-Port OC-3c/STM-1 and
OC-12c/STM-4 POS SPA configured for OC-12 provide the following optical fiber options:
• Multimode—622.08-Mbps, OC-12 optical fiber (SONET STS-12c or SDH STM-4)
Use a multimode optical fiber that has a core/cladding diameter of 62.5/125 microns.
• Single-mode—622.08-Mbps, OC-12 optical fiber (SONET STS-12c or SDH STM-4)
Use a single-mode optical fiber that has a modal-field diameter of 8.7 ± 0.5 microns. (Nominal
diameter is approximately 10/125 microns.)
For single-mode and multimode optical fiber connections, you can use either a duplex LC-type cable (see
Figure 2-31) or two simplex LC-type cables, one for transmit (TX) and one for receive (RX).
Use single-mode (for short-, intermediate- or long-reach configurations) or multimode optical fiber
cable to connect your router to a network or to connect two OC-3-equipped or OC-12-equipped routers
back-to-back. Long-range SFP optical transceiver modules (for long-reach configurations) cannot be
connected back-to-back without using an attenuator between the two of them.
Figure 2-31 LC-Type Cable
/ / / /
/ /
TXRX
84929

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco 12000 - Series Chassis Modular Expansion Base and is the answer not in the manual?

Cisco 12000 - Series Chassis Modular Expansion Base Specifications

General IconGeneral
BrandCisco
Model12000 - Series Chassis Modular Expansion Base
CategoryNetwork Router
LanguageEnglish

Related product manuals