Cisco ASR 1002 Quick Start Guide

13
Step 3 Configure to a fixed speed through the command-line interface (CLI) commands.
Connect the Shared Port Adapter Cables
The instructions for connecting the cables for the shared port adapters installed in the Cisco ASR 1002 Router are contained in
the Cisco ASR 1000 Series Aggregation Services Routers SPA and SIP Hardware Installation Guide.
Install the Cables Using the Cable-Management Bracket
Cables coming off the front side of the Cisco ASR 1002 integrated route processor and SPAs utilize the chassis level
cable-management brackets provided on the chassis rack-mount brackets (see Figure 10).
Figure 10 Cisco ASR 1002 Integrated Route Processor Cable-Management
To secure shared port adapter interface cables and input or output cables connected to the Cisco ASR 1002 Router, follow these
steps:
Step 1 When installing the network interface cables, route the cables up to and through the cable-management bracket ‘U’
device. If you are using very thin cables that slip through the bracket openings, insert nylon cable ties through the holes
in the bracket and wrap them around the cables to secure them.
Step 2 Route the excess cable out through either end of the bracket, coil it, and secure it to the rack using nylon cable ties or
some other mode of attachment.
Step 3 It might be necessary to bundle longer cables to avoid tangling them. Do this at the cable-management bracket or at
the rack, but leave enough slack in the cables to remove a Cisco ASR 1000-ESP5 and change cables as required. Also,
do not block the power supply air vents with cables.
This completes the procedure for installing the cables in the cable-management bracket.
1
BITS cable
4
AUX cable
2
MGMT cable
5
Cable-management U feature device
3
CON cable
A
SR
1
0
0
2
s
ta
t
pw
r
m
i
n
m
aj
c
ri
t
S
P
A
-
4
X
OC3
-
P
OS
S
TA
T
U
S
0
1
2
3
C
/A
A/L
C
/A
A
/L
C
/A
A/L
C
/A
A
/
L
S
P
A
-
4X
OC3
-
P
OS
S
T
A
T
U
S
0
1
2
3
C
/A
A
/
L
C
/A
A
/L
C/A
A
/L
C
/A
A
/L
ST
A
T
Q
E
0
Q
E
1
Q
E
2
Q
E
3
B
O
O
T
CA
RR
I
E
RL
I
N
K
P
W
R
S
T
A
T
M
T
S
M
G
M
TA
UX CO
N
S
P
A
-
4
X
OC3
-
P
OS
S
T
A
T
U
S
0
1
2
3
C
/
A
A
/
L
C
/
A
A
/L
C
/A
A
/
L
C/A
A
/
L
280287
5
5
1 2 3 4

Cisco ASR 1002 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.3
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
DHCP client	-
Supported network protocols	BGP, GRE, OSPF, DVMRP, EIGRP, IS-IS, IGMPv3, PIM-SM, PIM-SSM
Ethernet LAN (RJ-45) ports	4
Security algorithms	SSH
VPN tunnels quantity	8000
Safety	UL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
Certification	FCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory	4096 MB
AC input voltage	85 - 264 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (typical)	560 W
Operating altitude	0 - 3048 m
Storage temperature (T-T)	0 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 90 %
Product color	Gray
Rack capacity	2U

Weight and Dimensions

Depth	461 mm
Width	437.4 mm
Height	89 mm
Weight	- g