Cisco ASR 1002 Quick Start Guide

28
Save the Running Configuration to NVRAM
To store the configuration or changes to your startup configuration in NVRAM, use the copy running-config startup-config
command to save your configuration changes to the startup configuration so that the changes will not be lost if the software
reloads or a power outage occurs. For example:
Router# copy running-config startup-config
Building configuration...
It might take a minute or two to save the configuration. After the configuration has been saved, the following output appears:
[OK]
Router#
This task saves the configuration to NVRAM.
To review changes you make to the configuration, use the EXEC mode show startup-config command to see the changes and
copy run-start command stored in NVRAM.
Note Using the copy run-start command saves the configuration settings that you created in the router using configuration
mode and the setup facility. If you fail to do this, your configuration will be lost the next time you reload the router.
Perform Other Configuration Tasks
To make advanced configuration changes after you establish the basic startup configuration for your router, refer to the Cisco
ASR 1000 Series Aggregation Services Routers Software Configuration Guide and modular configuration and modular
command reference publications in the Cisco IOS software configuration documentation set that corresponds to the software
release installed on your Cisco hardware. These publications contain additional information on using the configure command.
The configuration publications also provide information about the following tasks:
• Understanding command modes
• Booting and rebooting the router
• Understanding software packages and architecture for the Cisco ASR 1002 Router
• Software Upgrades
7 After Installation
Follow the instructions in this section to replace field-replaceable units (FRUs) after installation. The Cisco ASR 1002 Router
supports the following components as FRUs: Cisco ASR1000-ESP5, shared port adapters, and power supplies.
Note For a complete list of Cisco ASR 1000 Series Routers field replaceable units, go to the Cisco ASR 1000 Series
Aggregation Services Router Hardware Installation and Initial Configuration Guide, Chapter 8.
The following topics are covered in this section:
• Power Off the Cisco ASR 1002 Router, page 29
• Replace the Cisco ASR1000-ESP5 or ASR1000-ESP10, page 29
• Replace the Shared Port Adapters, page 30
• Replace a Power Supply in the Cisco ASR 1002 Router, page 31
Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030

Cisco ASR 1002 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.3
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
DHCP client	-
Supported network protocols	BGP, GRE, OSPF, DVMRP, EIGRP, IS-IS, IGMPv3, PIM-SM, PIM-SSM
Ethernet LAN (RJ-45) ports	4
Security algorithms	SSH
VPN tunnels quantity	8000
Safety	UL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
Certification	FCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory	4096 MB
AC input voltage	85 - 264 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (typical)	560 W
Operating altitude	0 - 3048 m
Storage temperature (T-T)	0 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 90 %
Product color	Gray
Rack capacity	2U

Weight and Dimensions

Depth	461 mm
Width	437.4 mm
Height	89 mm
Weight	- g