Cisco ASR 1002 Quick Start Guide

18
Step 9 Connect the ground, positive, and negative leads to the power source.
Step 10 Turn the branch source breaker on.
Step 11 Turn the power supply switch to the On (I) position.
Step 12 Verify that the LEDs illuminate.
This completes the procedure for connecting DC-input power.
Verifying Power Supply operation
Follow this procedure to verify power supply is operating correctly.
Step 1 Check that the power supply LEDs are:
• INPUT OK is green
• FAN OK is green
• OUTPUT FAILED is not illuminated
Step 2 To ensure that the power supply state is OK, type the show platform command. This output sample is from a Cisco
ASR1002 router.
MCP_SCAL_R1#sho env all
Chassis type: ASR1002
The following output displays:
If the LEDs indicate a power problem or the power supply state is ps,fail, then contact a customer service representatives for
assistance or additional instructions.
Start the Cisco ASR 1002 Router
After installing your Cisco ASR 1002 Router and connecting cables, start the router as follows.
Check the following conditions before you start the Cisco ASR 1002 Router:
• The Cisco ASR 1002 Router has one slot for FP0 with three subslots for SPAs, subslots 1, 2, and 3. Make certain that each
shared port adapter is firmly seated in its subslot and its captive screws are securely tightened.
• The Cisco ASR1000-ESP5 or ASR1000-ESP10 forwarding processor in the Cisco ASR 1002 router is inserted in slot F0, is
firmly seated in its slot, and its captive screws are securely tightened.
• All network interface cables are connected.
• The console terminal is turned on.
Slot Type State Insert Time
R0 ASR1000-RP1 ok,active 00:03:19
F0 ASR1000-ESP10 ok,active 00:03:19
P0 ASR1002-PWR-AC ok 00:02:50
P1 ASR1002-PWR-AC ps, fail 00:02:50
Slot CPLD Version Firmware Version
R0 08060301 12.2(0:0)
F0 08041102 12.2(33r)XN2

Cisco ASR 1002 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.3
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
DHCP client	-
Supported network protocols	BGP, GRE, OSPF, DVMRP, EIGRP, IS-IS, IGMPv3, PIM-SM, PIM-SSM
Ethernet LAN (RJ-45) ports	4
Security algorithms	SSH
VPN tunnels quantity	8000
Safety	UL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
Certification	FCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory	4096 MB
AC input voltage	85 - 264 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (typical)	560 W
Operating altitude	0 - 3048 m
Storage temperature (T-T)	0 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 90 %
Product color	Gray
Rack capacity	2U

Weight and Dimensions

Depth	461 mm
Width	437.4 mm
Height	89 mm
Weight	- g