Cisco ASR 1002 Quick Start Guide

29
Power Off the Cisco ASR 1002 Router
This section explains how to shut down the Cisco ASR 1002 Router. It is recommended that before turning off all power to the
chassis, you issue the reload command. This insures that the operating system cleans up all the file systems. Once the reload
operation is complete, then the Cisco ASR 1000 Series router can be powered off safely.
To remove power from the Cisco ASR 1002 Router, follow this procedure:
Step 1 Slip on the ESD-preventative wrist strap that was included in the accessory kit.
Step 2 Before you shutdown the router, issue the IOS reload command to halt the system and then wait for ROM Monitor to
execute before proceeding to the next step. The following screen shot shows an example of the reload command:
Router#reload
Proceed with reload? [confirm]
*Jun 18 19:38:21.870: %SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload command.
Step 3 Remove any power cables from the Cisco ASR 1002 Router.
a. For AC power supplies, switch the circuit breaker to the off (O) position and unplug the AC power cord from the
power outlet.
b. For DC power supplies, place the power switch in the Standby position. Then remove the terminal block plug from the
DC power supply.
Note After powering off the router, wait a minimum of 30 seconds before powering it on again.
Replace the Cisco ASR1000-ESP5 or ASR1000-ESP10
This section provides instructions for removing the Cisco ASR1000-ESP5 or ASR1000-ESP10 from the Cisco ASR 1002 Router.
The Cisco ESP5 and ESP10 are Cisco Quantum Flow Processors (QFP) for the Cisco ASR 1002 Router. The Cisco ESP5 and
ESP10 are individual FRUs and support online insertion and removal operation. Before you begin, make certain the chassis is
grounded.
To remove the Cisco ESP5 or ESP10 from the Cisco ASR 1002 Router, follow this procedure:
Step 1 Slip on the ESD-preventative wrist strap that was included in the accessory kit. Loosen the captive screws on the Cisco
ESP5 or ESP10.
Step 2 Using the handles on both sides of the module, with two hands, gently slide the Cisco ESP5 or ESP10 out of the chassis
slot.
Note Handle the Cisco ESP5 and ESP10 by the carrier edges only; never touch the printed circuit board components or
connector pins.
Step 3 Place the Cisco ESP5 or the ESP10 on an antistatic surface with its printed circuit board components facing upward or
in a static shielding bag.
You have completed the procedure for removing the Cisco ESP5 or ESP10.
To install the Cisco ESP5 or ESP10 in the Cisco ASR 1002 Router, follow this procedure:
Step 1 Slip on the ESD-preventative wrist strap that was included in the accessory kit.

Cisco ASR 1002 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.3
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
DHCP client	-
Supported network protocols	BGP, GRE, OSPF, DVMRP, EIGRP, IS-IS, IGMPv3, PIM-SM, PIM-SSM
Ethernet LAN (RJ-45) ports	4
Security algorithms	SSH
VPN tunnels quantity	8000
Safety	UL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
Certification	FCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory	4096 MB
AC input voltage	85 - 264 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (typical)	560 W
Operating altitude	0 - 3048 m
Storage temperature (T-T)	0 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 90 %
Product color	Gray
Rack capacity	2U

Weight and Dimensions

Depth	461 mm
Width	437.4 mm
Height	89 mm
Weight	- g