7
Basic Operations
Note:
• Refer
to
the diagrams
in
"3.
CONTROLS"
when reading this chapter.
A CAUTION
Listening to the unit at or near maximum
volume level can be harmful to your
hearing.
Power On I
Off
Note:
• Start the engine before using this unit.
•
Be
careful about using this unit for a long
time without running the engine.
If
you
drain the battery too far. you may not
be
able to start the engine and this can reduce
the service life of the battery.
1.
Start the engine. The power button I knob
illumination
on
the unit will light
up.
~
EngineON
\...?W.J
position
2.
Press the
[<!>
SRC] button
on
the front
panel or remote control to turn
on
the
power under standby mode. The unit goes
back
to
the last status after power
on.
3.
Press and hold the
[<!>
SRC] button
on
the
front panel or the remote control to turn off
the power.
Mute
Press the [MUTE] button
on
the remote control
to mute the volume from the unit.
Note:
Doing the operation above again or adjusting
volume
will release muting.
M606
Volume Adjustment
STANDARD:
Rotate the [VOLUME] knob
on
the front panel or press the [
..&.
] or [ .,. ]
button
on
the remote control.
MUL Tl ZONE:
In
Volume adjustment mode,
rotate the
[UP/DOWN] knob to select ZONE
number, then rotate the
[VOLUME] knob to
adjust.
The adjustable range of volume
is
0
to
40.
A CAUTION
While driving, keep the volume level at
which external sounds can still be heard.
Changing Sources
Press the
[(!)
SAC] button to change the
operation mode.
Changing the Display
Press the [DISP] button
on
the front panel or
remote control to switch the display informa-
tion from clock, station information (radio
mode), or track information (USB mode).
RESETTING THE
UNIT
If you have the following problems, please
press
[RESET] button.
• Unit can not power
on
• Nothing happens when buttons are pressed
• Display
is
not accurate
Note:
* When
the
[RESET] button
is
pressed, preset
radio stations, audio settings, etc. stored
in
memory are retained.
oO
o o 0
~~
[RESET]
System Setup
Changing Adjustment Settings
1 . Press and hold [DISP] button to switch to
system setup mode.
2.
Press the
[~]or
[..,...]button
to
select
the
"item name".
3.
Rotate the [UP/DOWN] knob to select the
"desired setting value".
* For some options, you should press the
[ENT] button to adjust the setting value.
4.
After completing the setting adjustment,
press the
[MENU] button to return to the
previous mode.
CLOCK
1.
Press the [ENT] button.
2.
Press the
[~]or
[..,...]button
to
select
the hour or the minute.
3.
Rotate the [UP/DOWN] knob to set the
correct time.
* The clock
is
displayed
in
12-hour format
by default.
4.
Press the [ENT] button to store the time
into memory.
Note:
• The clock can only be
set
while the unit
is on.
If
you drain
or
remove the boat's
battery
or
take out this unit, the clock will
reset. While setting the clock,
if
another
button
or
operation is selected, the clock
set mode is canceled.
ZONE SELECT
1.
Rotate the
[UP/DOWN]
knob to select
STANDARD or
MULTI ZONE.
2.
Press the [ENT] button to confirm.
ZONE LINK (MUL Tl ZONE mode)
1.
Press the [ENT] button.
2.
Rotate the
[UP/DOWN]
knob to select
the
ZONE number from
2,
3,
4.
Press the
[
~
]
or
[ ..,... ] button to select "LNK
ZONE"
or "UNLNK ZONE".
3.
Press the [ENT] button to confirm.
DX/LO (RADIO mode)
Rotate the [UP/DOWN] knob to choose radio
local or distant at
RADIO mode.
•
LO:
Only stations with strong signal can
be
received.
•
OX:
Stations with strong and weak sig-
nals can
be
received.
AUX SENS (AUX mode)
Rotate the [UP/DOWN] knob
to
choose AUX
Input sensitivity LOW, MID or HIGH
in
AUX
mode.
PARENTAL (SiriusXM mode)
Change parental password. Default code
is
"0000"
LOCK
CH
(SiriusXM mode)
Lock the current channel
UNLOCK ALL CH (SiriusXM mode)
Unlock
all
parental locked channels.
SELECT
The "SELECT" menu is intended to auto-
matically pair with a stored mobile device.
This unit can store a maximum of three
mobile devices. The
mobile devices will
be
stored
in
the order they are paired to the
unit.
If you wish to add a different device
than those already paired, you
will
need to
delete the unwanted mobile device from the
"DELETE" menu.
DELETE
1.
Press the [ENT] button.
2.
Rotate the [UP/DOWN] knob to choose
the paired mobile phone name from the
pairing list.
3.
Press the [ENT] button.to confirm.
DISCON (BT mode) .
Disconnect
currently
connected
mobile
phone.
1.
Press the [ENT] button, mobile phone
displays are currently connected.
2.
Press the [ENT] button to disconnect.
To Next Page
Loading...
Need help?
General
