iNSTALLATiON STEP 6
Irestall the Door Control
Locate door control within sight of door, at a minimum
height of 5 feet (1.5 m) where small children cannot
reach, away from moving parts of door and door
hardware. If installing into drywall, drill 5/32" holes and
use the anchors provided. For pre-wired installations (as
in new home construction), it may be mounted to a single
gang box (Figure 1).
1. Strip 7/16" (11 mm) of insulation from one end of bell
wire and connect to the two screw terminals on back of
door control by color: white wire to 2 and white/red
wire to the 1 (Figure 2).
2. Remove white cover by gently prying at slot in top of
the cover with a small flat head screwdriver (Figure 3).
Fasten with 6ABx1-1/4" self-tapping screws (drywall
installation) or 6-32x1" machine screws (into gang box)
as follows:
• Install bottom screw, allowing 1/8" (3 mm) to protrude
above wall surface.
• Position bottom of door control on screw head and
slide down to secure. Adjust screw for snug fit.
• Drill and install top screw with care to avoid cracking
plastic housing. Do not overtighten.
• Insert top tabs and snap on cover.
3. (For standard installation only) Run bell wire up wall
and across ceiling to motor unit. Use insulated staples
to secure wire in several places. Do not pierce wire
with a staple, creating a short or open circuit.
4. Strip 7/16" (11 mm) of insulation from end of bell wire.
Connect bell wire to the quick-connect terminals as
follows: white to white and white/red to red (Figure 4).
NOTE: When connecting multiple door controls to the
opener, twist same color wires together. Insert wires
into quick-connect holes: white to white and red/white
to red.
5. Position the antenna wire as shown.
6. Use tacks or staples to permanently attach entrapment
warning label to wall near door control, and manual
release/safety reverse test label in a prominent
location on inside of garage door.
NOTE: DO NOT connect power and
operate opener at this time. The trolley
will travel to the full open position but
wifl not return to the close position until
the sensor beam is connected and
properly aligned.
To prevent possible SERIOUSINJURYor DEATHfrom
electrocution:
• Besure power is NOTconnected BEFOREinstallingdoor
control.
• Connect ONLYto 24 VOLTlowvoltage wires.
To prevent possible SERIOUSINJURYor DEATHfrom a
closing garagedoor:
• Install door control within sight of garagedoor, out of
reachof children at a minimum height of 5 feet (1.5 m),
and awayfrom ALL moving parts of door.
• NEVERpermit children to operateor play with door control
push buttons or remotecontrol transmitters.
• Activate door ONLYwhen itcan be seen clearly, is
properly adjusted, andthere are no obstructions to door
travel.
• ALWAYSkeepgaragedoor in sight until completely
closed. NEVERpermit anyoneto cross path of closing
garagedoor.
HARDWARE SHOWN ACTUAL SIZE
_ Insulated
(std installation) Staples
(pre-wired) Drywall Anchors
Figure 1 _ Figure 2
PRE-WIRED II{_,_/_'1 _ Top
INSTALLATION _ Mounting
Hole
Terminal
Screws
Bottom
Mounting
24 Volt 2-Conductor Wire LL2:::::::_I::::::_tJ) Hole
Bell Wire in Gang Box (BACK VIEW)
Figure 3
To Replace,
Insert Top
Tabs First _ -"
Lighted
Push Button
\
Figure 4 -_ j
Quick-Connect
Bell Wire Terminals
Door Control
Connections
Strip wire 7/16" (11 mm)
To release or insert wire, push
in tab with screwdriver tip
Antenna
17
Red White Grey
To Next Page
Loading...
Need help?
General
