D-Link DIR-600 User Manual

93D-Link DIR-600 User Manual
Section 4 - Security
Congure WEP
It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish
wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the
added overhead.
1. Log into the web-based conguration by opening a web browser
and entering the IP address of the router (192.168.0.1).
2. Click on Setup and then click Wireless Settings on the left side.
3. Click the Manual Wireless Connection Setup button.
4. Next to Security Mode, select Enable WEP Wireless Security (basic).
5. Next to WEP Encryption, select 64bit or 128bit.
6. Next to Default WEP Key, select the WEP key you would like to use
as the default WEP key. The available options are WEP Key 1, WEP
Key 2, WEP Key 3, or WEP Key 4.
7. Enter the WEP key you would like to use in the WEP Key eld.
8. Click Save Settings to save your settings. If you are conguring the router with a wireless adapter, you will lose connectivity
until you enable WEP on your adapter and enter the same WEP key as you did on the router.

D-Link DIR-600 Specifications

Wireless Signal Rates

IEEE 802.11n 20MHz Channel	65/72.2 Mbps (max)
IEEE 802.11n 40MHz Channel	135/150 Mbps (max)
IEEE 802.11g	54 Mbps - 48 Mbps - 36 Mbps - 24 Mbps - 18 Mbps - 12 Mbps - 11 Mbps - 9 Mbps - 6 Mbps

Operating Environment

operating temperature	0 °C to 40 °C (32 °F to 104 °F)
storage temperature	-20 °C to 65 °C (-4 °F to 149 °F)
humidity range	10% to 95% (non-condensing)

Frequency Range

wireless frequency range	2.4 GHz to 2.4835 GHz (802.11g/n)

Weight and Dimensions

length	160 mm (6.3 inches)
width	120 mm (4.72 inches)
height	59 mm (2.32 inches)

Summary

Product Overview

System Requirements

Features

Hardware Overview

Installation

Before You Begin

Wireless Installation Considerations

Connect to Cable/DSL/Satellite Modem

Step-by-step guide to connect the DIR-600 to a modem for internet access.

Connect to Another Router

Instructions for connecting the DIR-600 to an existing router as an access point or switch.

Getting Started

Configuration

Web-based Configuration Utility

Explains how to access and use the router's web interface for setup.

Setup

Guides on router setup and internet connection configuration.

Wireless Settings

Options for configuring wireless network name, security, and channel.

Network Settings

Configure local network settings and DHCP server options.

Advanced Settings

Configure advanced network features like firewall, QoS, and IPv6.

Tools

Manage router settings including admin, time, email, system, and firmware.

Status

Security

Wireless Security

Options for protecting your wireless network data from intruders.

What is WPA?

Wireless Connection Setup Wizard

Guides users through connecting a wireless device to the network.

Add Wireless Device with WPS Wizard

Wizard for adding wireless devices using Wi-Fi Protected Setup (WPS).

Configure WEP

Steps to enable and configure Wired Equivalent Privacy encryption for wireless security.

Configure WPA/WPA2-Personal (PSK)

Configure Wi-Fi Protected Access with Pre-Shared Key for enhanced wireless security.

Configure WPA/WPA2-Enterprise (RADIUS)

Connecting to a Wireless Network

Connect to a Wireless Network Using Windows 7

Using Windows Vista

Using Windows XP

Configure WPA-PSK

Troubleshooting

Accessing the Web-based Configuration Utility

Forgot Password

Steps to reset the router if the administrator password is forgotten.

Connectivity Issues

Networking Basics

Check Your IP Address

Statically Assign an IP Address