D-Link xStack DES-3200 Series User Manual

xStack® DES-3200 Series Layer 2 Ethernet Managed Switch CLI Reference Manual
14
5
16
VLAN COMMANDS
The VLAN commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following
table:
Command Parameters
create vlan <vlan_name 32> tag <vlanid 1-4094> {advertisement}
delete vlan <vlan_name 32> | vlanid <vidlist>
create vlan vlanid <vidlist> {advertisement}
delete vlan vlanid <vidlist>
config vlan vlanid <vidlist> { [ add [ tagged | untagged | forbidden ] | delete ]
<portlist> | advertisement [ enable | disable ] | name <vlan_name
32>} (1)
config vlan <vlan_name 32> {[add [tagged | untagged | forbidden] | delete]
<portlist> | advertisement [enable | disable]} (1)
enable pvid auto_assign
disable pvid auto_assign
show pvid auto_assign
config gvrp [<portlist> | all] {state [enable | disable] | ingress_checking [enable
| disable] | acceptable_frame [tagged_only | admit_all] | pvid
<vlanid 1-4094>} (1)
enable gvrp
disable gvrp
show vlan {[<vlan_name 32> | vlanid <vidlist> | ports <portlist>]}
show gvrp {<portlist>}
Each command is listed, in detail, in the following sections:
create vlan
Used to creat
e a VLAN on the Switch.
Purpose
cre
ate vlan <vlan_name 32> tag <vlanid 1-4094> {advertisement}
Syntax
This
command allows the user to create a VLAN on the Switch.
Description
Parameters
<vlan_name 32>  The name of the VLAN to be created.
<vlanid 1-4094>  The VLAN ID of the VLAN to be created. Allowed
values = 1-4094
advertisement  Specifies that the VLAN is able to join GVRP. If
this parameter is not set, the VLAN cannot be configured to have
forbidden ports.
Each VLAN n
ame can be up to 32 characters. Up to 4094 static
VLANs may be created per configuration. Only Administrator-level
users can issue this command.
Restrictions
Example usage:

D-Link xStack DES-3200 Series Specifications

General

Managed	Yes
Layer	Layer 2
MAC Address Table Size	8K
Quality of Service (QoS)	802.1p
Security Features	ACL, 802.1X, Port Security
Jumbo Frame Support	Up to 9KB
Dimensions	Varies by model
Weight	Varies by model
Operating Temperature	0°C to 40°C
Storage Temperature	-40°C to 70°C
Standards Compliance	IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z, IEEE 802.3x, IEEE 802.1D, IEEE 802.1w, IEEE 802.1s, IEEE 802.1Q, IEEE 802.1p
Forwarding Rate	13.1 Mpps (48-port)

Summary

Introduction

Accessing the Switch via the Serial Port

Details the process of connecting to the switch using a serial port and terminal emulation.

Setting the Switch’s IP Address

Explains how to assign an IP address to the switch for network management.

Command Syntax

Angle Brackets < >

Encloses a variable or value that must be specified in a command.

Square Brackets [ ]

Encloses a required value or set of required arguments for a command.

Line Editing Key Usage

Explains the usage of keys for editing commands at the CLI prompt.

Basic Switch Commands

create account

Creates new user accounts with specified privilege levels and usernames.

show switch

Displays general information about the switch's status and configuration.

Switch Port Commands

config ports

Configures various settings for Ethernet ports, including speed, duplex, and state.

Network Management (SNMP) Commands

create snmp user

Creates a new SNMP user with specified credentials and access levels.

QoS Commands

config bandwidth_control

Configures bandwidth control on a port-by-port basis for traffic management.

VLAN Commands

create vlan

Creates a new VLAN on the switch, assigning a name and VLAN ID.

802.1X Commands

enable 802.1x

Enables the 802.1X Network Access Control application on the switch.

Access Control List (ACL) Commands

create access_profile

Creates an access profile to define criteria for packet forwarding or filtering.

SSH Commands

enable ssh

Enables the Secure Shell (SSH) protocol for secure remote management.

SSL Commands

enable ssl

Enables the Secure Sockets Layer (SSL) function for secure communication.

Appendix B - Password Recovery Procedure

Complete these steps to reset the password

Outlines the physical access and hotkey procedure to enter password recovery mode.

Appendix C - RADIUS Attributes Assignment