Daikin BRC1E53 User Manual

BRC1E53 Installer reference guide
4P419250-1
–
2015.10
2
Safety Precautions
1. Safety Precautions
The original instructions are written in English. All other languages are translations of the original
instructions.
 Also see the installation manual attached to the indoor unit.
Please read these Safety Precautions carefully before installing the remote controller.
● This manual classies the precautions into WARNING and CAUTION. They both contain important
information regarding safety. Be sure to follow all the precautions below.
WARNING
Failure to follow these instructions properly may result in personal
injury or loss of life.
CAUTION
Failure to observe these instructions properly may result in property
damage or personal injury, which may be serious depending on the
circumstances.
● After completing the installation, conduct a trial operation to check for faults and explain to the
customer how to operate the air conditioner with the aid of the operation manual. Ask the customer
to store the installation and operation manual for future reference.
WARNING
Ask your dealer or qualied personnel to carry out installation work.
Do not attempt to install the remote controller yourself. Improper installation may result in water
leakage, electric shocks or re.
Consult your local dealer regarding relocation and reinstallation of the remote controller.
Improper installation work may result in leakage, electric shocks or re hazards.
Install the remote controller in accordance with the instructions in this installation manual.
Improper installation may result in water leakage, electric shocks or re.
Be sure to use only the specied accessories and parts for installation work.
Failure to use the specied parts may result in the unit falling down, water leakage, electric shocks
or re.
Install the remote controller on a foundation strong enough to withstand the weight of the remote
controller.
Insufcient strength may result in the remote controller falling down and causing injury.
Electrical work must be performed in accordance with the relevant local and national regulations and
with the instructions in this installation manual.
Be sure to use a dedicated power supply circuit only. Insufcient power circuit capacity and improper
workmanship may result in electric shocks or re.
Always perform installation work with the power turned off.
Touching electric parts may result in electric shock.
Do not disassemble, reconstruct or repair.
This may result in electric shock and/or re.
Make sure that all wiring is secured, the specied wires are used and that there is no strain on the
terminal connections or wires.
Improper connections or securing of wires may result in abnormal heat build-up or re.
The choice of materials and installations must comply with the applicable national and international
standards.

Daikin BRC1E53 Specifications

General

Brand	Daikin
Model	BRC1E53
Category	Remote Control
Language	English

Summary

1. Safety Precautions

3. Remote Controller Installation Procedure

3-1 Location Selection

Guidelines for selecting the installation location based on safety.

3-2 Wiring Through Hole

Instructions for creating a wiring hole on the wall for rear cable exit.

3-3 Wiring Outlet Direction

Explains different options for wiring outlet direction on the controller.

3-4 Conduct Wiring

Details on how to conduct wiring for the remote controller.

3-5 Lower Case Fixing

Steps for fixing the lower case of the remote controller to the wall or switchbox.

3-6 Upper Case Attachment

Instructions for attaching the upper case to the lower case.

4. Remote Controller Functions and Buttons

4-1 Button and Menu Overview

Overview of remote controller buttons and main menu options.

4-2 Button Operation Details

Detailed explanation of how each button on the remote controller functions.

5. Power-On Procedures

Single Controller Setup

Steps for powering on when controlling a single indoor unit.

Dual Controller Setup

Steps for powering on when controlling a single indoor unit with two controllers.

6. Field Settings Configuration

6-1 Accessing Service Settings

Accessing the Service Settings menu for field configurations.

6-2 Selecting Field Settings

Navigating to and selecting the "Field Settings" option.

6-3 Setting Mode Numbers

Selecting mode numbers for field settings.

6-4 Individual Unit Configuration

Configuring individual indoor units within a group setting.

6-5 Setting Second Code Numbers

Selecting second code numbers for specific field settings.

6-6 Confirming and Saving Settings

Confirming and saving the configured field settings.

7. Test Operation (SkyAir Only)

7-1 Pre-Operation Checks

Pre-operation steps including power-on time and valve checks.

7-3 Setting Cooling Mode

Setting the operation mode to cooling for testing.

7-5 Starting Test Operation

Starting the test operation from the Service Settings menu.

7-15 Maintenance Information Check

Navigating to and checking Maintenance Information for errors.

8. Checking Error History

8-1 Accessing Service Settings

8-2 Navigating to Error History

8-3 Accessing RC Error History

8-4 Viewing Error Records

11. Energy Demand Control

11-1 Accessing Service Settings

11-2 Navigating to Demand Menu

11-7 Enabling or Disabling Demand

11-9 Saving Enable/Disable Setting

12. Clock & Calendar Settings

12-3 Accessing Date & Time

12-4 Setting Date and Time Values

12-6 Saving Date and Time

14. Prohibit Buttons Configuration

14-1 Accessing Main Menu

14-4 Navigating to Prohibit Buttons

14-5 Configuring Button Lock/Unlock

14-8 Disabling/Enabling Buttons

15. Function Prohibition

15-1 Accessing Main Menu

15-4 Navigating to Function Prohibition

15-5 Configuring Function Lock/Unlock

15-7 Saving Function Prohibition

16. Prohibit Mode Configuration

16-1 Accessing Main Menu

16-4 Navigating to Prohibit Mode

16-5 Configuring Operation Modes

19. Single and Dual Setpoint Mode

19-3 Setting Setpoint Mode

19-5 Saving Setpoint Mode

21. Software Update with Updater

22. Connection Diagrams

22-1 Typical Layout

22-3 Group Control: Main + Sub Controller

22-4 Group Control: Controller + Digital Inputs Adapter

22-5 Controller + DIII Central Control