Danfoss VLT 5003 User Manual

Tightening-up torques and screw sizes
The table shows the torque required when fitting ter-
minals to the adjustable frequency drive. For VLT
5001-5027 200-240 V, VLT 5001-5102 380-500 V and
VLT 5001-5062 525-600 V, the cables must be fas-
tened with screws. For VLT 5032-5052 200-240 V,
VLT 5122-5552 380-500 V, VLT 5042-5602 525-690
V, the cables must be fastened with bolts.
These figures apply to the following terminals:
Line terminals Nos. 91, 92, 93
L1, L2, L3
Motor terminals
Nos. 96, 97, 98
U, V, W
Ground terminal
No. 94, 95, 99
Brake resistor terminals
81, 82
Load sharing
88, 89
VLT type
200-240 V
Torque [Nm] Screw/
Bolt size
Tool
5001-5006 0,6 M3 Slotted screw
5008 IP 20 1,8 M4 Slotted screw
5008-5011 IP 54 1,8 M4 Slotted screw
5011-5022 IP 20 3 M5 4 mm Allen wrench
5016-5022
31)
IP 54 3 M5 4 mm Allen wrench
5027 6 M6 4 mm Allen wrench
5032-5052
11,3 M8 (bolt and stud)
380-500 V
5001-5011 0,6 M3 Slotted screw
5016-5022 IP 20 1,8 M4 Slotted screw
5016-5027 IP 54 1,8 M4 Slotted screw
5027-5042 IP 20 3 M5 4 mm Allen wrench
5032-5042
3)
IP 54 3 M5 4 mm Allen wrench
5052-5062 6 M6 5 mm Allen wrench
5072-5102 IP 20 15 M6 6 mm Allen wrench
IP 54
2)
24 M8 8 mm Allen wrench
5122-5302
4)
19 M10 bolt 16 mm wrench
5352-5552
5)
19 M10 bolt (compression
lug)
16 mm wrench
525-600 V
5001-5011 0,6 M3 Slotted screw
5016-5027 1,8 M4 Slotted screw
5032-5042 3 M5 4 mm Allen wrench
5052-5062
6 M6 5 mm Allen wrench
525-690 V
5042-5352
4)
19 M10 bolt 16 mm wrench
5402-5602
5)
19 M10 bolt (compression
lug)
16 mm wrench
1) Brake terminals: 3,0 Nm, Nut: M6
2) Brake and load sharing: 14 Nm, M6 Allen screw
3) IP 54 with RFI - Line terminals 6 Nm, Screw: M6 - 5 mm Allen wrench
4) Load sharing and brake terminals: 9,5 Nm; Bolt M8
5) Brake terminals: 9,5 Nm; Bolt M8.
VLT
®
5000 Series
MG.51.C5.22 - VLT
p
is a registered Danfoss trademark. 57
Installation

Danfoss VLT 5003 Specifications

General

Brand	Danfoss
Model	VLT 5003
Category	DC Drives
Language	English