VLT
®
8000 AQUA
Introduction
■ Unpacking and ordering a VLT frequency converter
If you are in doubt as to which frequency converter
you have received and which options it contains,
use the following to find out.
■ Type code ordering number string
On the basis of your order, the frequency converter is
given an ordering number that can be seen from the
nameplate on the unit. The number may look as follows:
VLT-8008-A-T4-C20-R3-DL-F10-A00-C0
This means that the frequency converter ordered is a
VLT 8008 for three-phase mains voltage of 380-480 V
(T4) in Compact enclosure IP 20 (C20). The hardware
variant is with integral RFI filter, classes A & B (R3). The
frequency converter features a control unit (DL)witha
PROFIBUS option card (F10). No option card (A00)
and no conformal coating (C0) Character no. 8 (A)
indicates the application range of the unit: A =AQUA.
IP 00: This enclosure is only available for the larger
power sizes of the VLT 8000 AQUA series. It is
recommended for installation in standard cabinets.
IP 20/NEMA 1: This enclosure is used as standard
enclosure for VLT 8000 AQUA. It is ideal for
cabinet installation in areas where a high degree
of protection is required. This enclose also
permits side-by-side installation.
IP 54: This enclosure can be fitted direct to the
wall. Cabinets are not required. IP 54 units can
also be installed side-by-side.
Hardware variant
Theunitsintheprogrammeareavailableinthe
following hardware variants:
ST: Standard unit with or without control
unit. Without DC terminals, except for
VLT 8042-8062, 200-240 V
VLT 8016-8300, 525-600 V
SL: Standard unit with DC terminals.
EX: Extended unit with control unit, DC
terminals, connection of external 24 V
DC supply for back-up of control PCB.
DX: Extended unit with control unit, DC
terminals, built-in mains fuses and
disconnector, connection of external 24
V DC supply for back-up of control PCB.
PF: Standard unit with 24 V DC supply for
back-up of control PCB and built-in
main fuses. No DC terminals.
PS: Standard unit with 24 V DC supply
for back-up of control PCB. No DC
terminals.
PD: Standard unit with 24 V DC supply for
back-up of control PCB, built-in main
fuses and disconnect. No DC terminals.
RFI filter
Units for a mains voltage of 380-480 V and a motor
power of up to 7.5 kW (VLT 8011) are always
supplied with an integral class A1 & B filter. Units
for higher motor power than these can be ordered
either with or without an RFI filter. RFI filters are not
available for 525-600 V units.
A1 RFI is not offered on the VLT 8502 -8652 525-690V
Control unit (keypad and display)
All types of units in the programme, except for IP
54 units (and IP 21 VLT 8452-8652, 380-480 V and
VLT 8502-8652, 525-690 V), can be ordered either
with or without the control unit. IP 54 units always
come with acontrolunit.
All types of units in the programme are available
with built-in application options including a relay
card with four relays or a cascade controller card.
Conformal Coating
All types of units in the programme are available
with or without conformal coating of the PCB.
Please note VLT 8452-8652, 380-480 V and
VLT 8052-8652, 525-690 V are only available as
conformal coated.
MG.83.A2.02 - VLT is a registered Danfoss trademark
25
To Next Page
Loading...
Need help?
General