0-22 Display Line 1.3 Small
Q3-3 Closed-loop Settings
20-74 Maximum Feedback Level 20-93 PID Proportional Gain 20-14 Maximum Reference/Feedb.
0-23 Display Line 2 Large
Q3-30 Single Zone Int. Setpoint
20-79 PID Autotuning 20-94 PID Integral Time 6-10 Terminal 53 Low Voltage
6-11 Terminal 53 High Voltage 20-21 Setpoint 1 22-22 Low Speed Detection 22-21 Low Power Detection 22-87 Pressure at No-Flow Speed
6-12 Terminal 53 Low Current 20-22 Setpoint 2 22-23 No-Flow Function 22-22 Low Speed Detection 22-88 Pressure at Rated Speed
6-13 Terminal 53 High Current 20-81 PID Normal/ Inverse Control
22-24 No-Flow Delay
22-23 No-Flow Function 22-89 Flow at Design Point
6-14 Terminal 53 Low Ref./Feedb.
Value
20-82 PID Start Speed [RPM] 22-40 Minimum Run Time 22-24 No-Flow Delay 22-90 Flow at Rated Speed
6-15 Terminal 53 High Ref./Feedb.
Value
20-83 PID Start Speed [Hz] 22-41 Minimum Sleep Time 22-40 Minimum Run Time 1-03 Torque Characteristics
6-16 Terminal 53 Filter Time
Constant
20-93 PID Proportional Gain 22-42 Wake-up Speed [RPM] 22-41 Minimum Sleep Time 1-73 Flying Start
6-17 Terminal 53 Live Zero 20-94 PID Integral Time 22-43 Wake-up Speed [Hz] 22-42 Wake-up Speed [RPM]
Q3-42 Compressor Functions
6-20 Terminal 54 Low Voltage 20-70 Closed-loop Type 22-44 Wake-up Ref./FB Difference 22-43 Wake-up Speed [Hz] 1-03 Torque Characteristics
6-21 Terminal 54 High Voltage 20-71 PID Performance 22-45 Setpoint Boost 22-44 Wake-up Ref./FB Difference 1-71 Start Delay
6-22 Terminal 54 Low Current 20-72 PID Output Change 22-46 Maximum Boost Time 22-45 Setpoint Boost 22-75 Short Cycle Protection
6-23 Terminal 54 High Current 20-73 Minimum Feedback Level 2-10 Brake Function 22-46 Maximum Boost Time 22-76 Interval between Starts
6-24 Terminal 54 Low Ref./Feedb.
Value
20-74 Maximum Feedback Level 2-16 AC Brake Max. Current 22-26 Dry Pump Function 22-77 Minimum Run Time
6-25 Terminal 54 High Ref./Feedb.
Value
20-79 PID Autotuning 2-17 Over-voltage Control 22-27 Dry Pump Delay 5-01 Terminal 27 Mode
6-26 Terminal 54 Filter Time
Constant
Q3-4 Application Settings
1-73 Flying Start 22-80 Flow Compensation 5-02 Terminal 29 Mode
6-27 Terminal 54 Live Zero
Q3-40 Fan Functions
1-71 Start Delay 22-81 Square-linear Curve Approxi-
mation
5-12 Terminal 27 Digital Input
6-00 Live Zero Timeout Time 22-60 Broken Belt Function 1-80 Function at Stop 22-82 Work Point Calculation 5-13 Terminal 29 Digital Input
6-01 Live Zero Timeout Function 22-61 Broken Belt Torque 2-00 DC Hold/Preheat Current 22-83 Speed at No-Flow [RPM] 5-40 Function Relay
4-56 Warning Feedback Low 22-62 Broken Belt Delay 4-10 Motor Speed Direction 22-84 Speed at No-Flow [Hz] 1-73 Flying Start
4-57 Warning Feedback High 4-64 Semi-Auto Bypass Set-up
Q3-41 Pump Functions
22-85 Speed at Design Point [RPM] 1-86 Trip Speed Low [RPM]
20-20 Feedback Function 1-03 Torque Characteristics 22-20 Low Power Auto Set-up 22-86 Speed at Design Point [Hz] 1-87 Trip Speed Low [Hz]
Table 5.3 Quick Menu Structure
Programming Instruction Manual
52 Danfoss A/S © Rev. 2014-02-10 All rights reserved. MG16E222
55
To Next Page
Loading...
Need help?
General