Denon AVR-1912 User Manual

68
Playback in ZONE2 (Separate room)
•You can operate this unit so as to enjoy audio in a room (ZONE2)
other than the MAIN ZONE (room where the unit is located).
•You can simultaneously play back the same source in both the MAIN
ZONE, ZONE2. You can also play back separate sources in the MAIN
ZONE and ZONE2.
Audio output
Zone playback by speaker output
The ZONE2 audio signals are output from this unit’s SURR.BACK/AMP
ASSIGN speaker terminals using the amplifier assignment function.
nConnecting and setting the speakers
“Amp Assign” setting
(vpage83) and audio
signals output
Connecting the speakers
ZONE2
Output signal :
Stereo (L / R)
ZONE2
w q w q
(L) (R)
NOTE
It is not possible to play the digital audio signals input from the HDMI,
COAXIAL or OPTICAL connectors in ZONE2. Play using analog
connections (in stereo).
Playback
1
Press ZONE SELECT to switch the
zone mode to K (ZONE2).
Input source
select buttons
2
Press AMP to set the remote
control unit to AMP-operation
mode.
3
Press ZONE/DEVICE Z to turn on
the ZONE2 power.
The indicator on the display lights.
•Also press input source select button when
in standby mode, the power turns on.
•When ZONE/DEVICE X is pressed, ZONE2
turns off.
•Power in ZONE2 can be turned on or off by
pressing ZONE2 ON/OFF on the main unit.
4
Press the input source select
button.
The audio signal of the selected source
is output to ZONE2.
•To perform an operation with the main unit, press
ZONE2 SELECT
many times.
When power for both MAIN ZONE and ZONE2 is set to ON, power
of the MAIN ZONE only can be turned off. Select J (MAIN ZONE) in
step 1 then press ZONE/DEVICE X.
Adjusting the volume
Use M df to adjust the volume.
GAdjustable rangeH
– – – –80dB – –40dB – 18dB
(When the “Volume Display” (vpage92) setting is “Relative”)
GAdjustable rangeH
0 – 41 – 99
(When the “Volume Display” (vpage92) setting is “Absolute”)
•At time of purchase, “Volume Limit” (vpage 91) is set to
“–10dB (71)”.
Turn MASTER VOLUME after pressing ZONE2 SELECT on the main
unit to adjust the sound volume.
Turning off the sound temporarily
Press N.
The sound is reduced to the level set at “Mute Level” (vpage91)
in the menu.
•To cancel, either adjust the volume or press N again.
•The setting is canceled when the zone’s power is turned off.
Basic version
Advanced version
Information
Advanced version
vSee overleaf
BD

Denon AVR-1912 Specifications

General

Impedance	47 Ω
Receiver type	Surround
Frequency range	10 - 100000 Hz
Input sensitivity	200 mV
Audio output channels	7.1 channels
Audio A/D Converter (ADC)	24-bit/96kHz
Signal-to-Noise Ratio (SNR)	100 dB
Total Harmonic Distortion (THD)	0.08 %
Power output per channel (1KHz@6 Ohm)	125 W
Power output per channel (20-20KHz@8 Ohm)	90 W
HDMI in	6
Composite video in	3
Component video (YPbPr/YCbCr) in	1
Headphone connectivity	6.3 mm
Connectivity technology	Wired
Speakers connectivity type	Banana connector/Binding posts
Audio formats supported	AAC, FLAC, MP3, WAV, WMA
Image formats supported	JPG
Wi-Fi	No
Ethernet LAN	Yes
AM band range	520 - 1710 kHz
FM band range	87.5 - 107.9 MHz
Supported radio bands	AM, FM
Preset stations quantity	56
Supported video modes	1080i, 1080p, 480i, 480p, 576i, 576p, 720p
Analog signal format system	NTSC, PAL
Display	-
Product color	Black
Audio decoders	Dolby Digital EX, Dolby Digital Plus, Dolby Pro Logic II, Dolby Pro Logic IIx, Dolby Pro Logic IIz, Dolby TrueHD, DTS 96/24, DTS Neo:6, DTS-ES, DTS-ES (Discrete 6.1), DTS-ES (Matrix 6.1), DTS-HD
Apple docking compatibility	iPhone, iPod
AC input voltage	120 V
AC input frequency	60 Hz
Power consumption (standby)	0.1 W
Power consumption (typical)	460 W

Weight and Dimensions

Depth	382 mm
Width	435 mm
Height	167 mm
Weight	10200 g