12
LAST FUNCTION MEMORY
• This unit is equipped with a last function memory which stores the input and output setting conditions as they
were immediately before the power is switched off.
This function eliminates the need to perform complicated resettings when the power is switched on.
• The unit is also equipped with a back-up memory. This function provides approximately one week of memory
storage when the main unit’s power switch is off and with the power cord disconnected.
13
INITIALIZATION OF THE MICROPROCESSOR
When the indication of the display is not normal or when the operation of the unit does not shows the reasonable
result, the initialization of the microprocessor is required by the following procedure.
1
Switch off the unit using the main unit’s power
switch.
2
Press and hold the DIRECT buttons and
STEREO buttons at the same time, and turn the
main unit’s power switch on.
3
Check that the entire display is flashing with an
interval of about 1 second, and release your
fingers from the 2 buttons and the
microprocessor will be initialized.
2 Differences in surround mode names depending on the input signals
Input signals
PURE DIRECT, DIRECT
STEREO
HOME THX CINEMA
DTS SURROUND
DTS NEO:6
DOLBY DIGITAL
DOLBY PRO LOGIC
II
DSP SIMULATION
C
C
THX
E
DTS NEO:6
E
DOLBY
PRO LOGIC
II
C
C
C
THX
E
DTS NEO:6
E
DOLBY
PRO LOGIC
II
C
C
C
✳
THX MTRX6.1
THX5.1
✳
DTS ES MTRX
DTS SURROUND
E
E
E
C
C
C
THX5.1
✳
DTS ES MTRX
DTS 96/24
E
E
E
C
C
C
B
THX DSCRT6.1
THX MTRX5.1
B
DTS ES DSCRT6.1
DTS MTRX6.1
E
E
E
C
C
C
THX
E
DTS NEO:6
E
DOLBY
PRO LOGIC
II
C
C
C
✳
THX SURROUND EX
THX5.1
E
E
✳
6,1 SURROUND
DOLBY DIGITAL
E
C
ANALOG LINEAR PCM DTS (5.1 ch)
DTS 96/24(5.1 ch)
DTS (6.1 ch) D. D. (2 ch) D. D. (5.1 ch)
DTS DOLBY DIGITALSurround Mode
C : Selectable
✳ : The surround mode name differs depending on the “SB CH OUT” surround parameter setting.
B : The surround mode name differs depending on the input signal.
E : Not selectable
14
TROUBLESHOOTING
If a problem should arise,first check the following.
1. Are the connections correct ?
2. Have you operated the receiver according to the Operating Instructions ?
3. Are the speakers, turntable and other components operating property ?
If this unit is not operating properly, check the items listed in the table below. Should the problem persist, there
may be a malfunction.
Disconnect the power immediately and contact your store of purchase.
Symptom Cause Measures Page
DISPLAY not lit and sound not produced
when power switch set to on.
• Power cord not plugged in
securely.
• Check the insertion of the power
cord plug.
5
DISPLAY lit but sound not produced.
• Speaker cords not securely
connected.
• Input source selector button
position is not appropriate.
• Volume control set to minimum.
• MUTING is on.
• No digital signal is being input.
• Speaker A or B button is set to
“OFF”.
• Connect securely.
• Switch to the proper position.
• Turn volume up to suitable level.
• Switch off MUTING.
• Properly select a digital signal input
source.
• Set the button for the connected
speaker terminals to “ON”.
8
23
24
23
15
10
Nothing is displayed on monitor.
• AVC-A11SR’s video output jacks and
monitor’s input jacks are not
properly connected.
• Monitor TV’s input setting is wrong.
• Connections of the various
component’s video signals are not
unified.
• VIDEO OFF mode is set.
• PURE DIRECT mode is set.
• Check that the connections are
correct.
• Set the TV’s input selector to the
jacks to which video signals are
connected.
• Unify to composite or S jack.
• VIDEO ON mode is set.
• Mode other than PURE DIRECT
mode is set.
5, 6
5, 6
5, 6
26
26
No dts sound is produced.
• DVD player’s audio output setting is
not set to bit stream.
• DVD player is not dts-compatible.
• AVC-A11SR’s input setting is set to
analog.
• Make the DVD player’s initial
settings.
• Use a dts-compatible player.
• Set to AUTO or dts.
—
—
23
Copying from DVD to VCR is not
possible.
• Mode video software contains copy
prohibit signals.
• Copying is not possible.
—
No sound is produced from
subwoofer.
• Subwoofer’s power is not on.
• Subwoofer’s initial setting is set to
“No”.
• Subwoofer’s output is not
connected.
• Turn on the power.
• Set the setting to “Yes”.
• Connect properly.
—
10
8
No test tones are produced.
• Surround mode is set to a mode
other than Dolby Surround.
• Set to Dolby Surround.
—
No sound is produced from
surround speakers.
• Surround mode is set to “STEREO”. • Set to a mode other than
“STEREO”.
—
This unit does not operate properly
when remote control unit is used.
• Batteries dead.
• Remote control unit too far from this
unit.
• Obstacle between this unit and
remote control unit.
• Different button is being pressed.
• < and > ends of battery inserted in
reverse.
• Replace with new batteries.
• Move closer.
• Remove obstacle.
• Press the proper button.
• Insert batteries properly.
17
17
17
—
17
To Next Page
Loading...
Need help?
General
