Furuno LS-6100 User Manual

35
not use an “open” type lug ( ).
Optional equipment
Pin arrangement on NMEA port
Connector Remarks
1 TD-A
2 TD-B
IEC-61162-1/NMEA0183
3 RD-A
4 RD-B
IEC-61162-1/NMEA0183
5 +Vout
6 GND
Power output max. 100 mA*
7 FG
* = The LS-6100 can feed 12 V power to
GP-310B, GP-320B. The power voltage must
be at least 12 V to feed power to those units.
NMEA port setup
The NMEA port can function as an input
port or input/output port. Change the setting
to “In/In” when connecting GP-310B and a
wind sensor.
When connecting the GP-320B and a wind
sensor, first turn on “GPS WAAS” (in the
Installation menu) and then select “In/In” as
the NMEA port setting.
1. Turn on the power while pressing and
holding down the [MENU/ESC] key.
Continue pressing the [MENU/ESC] key
until the Installation menu appears.
2. Choose NMEA PORT, and then press
► to display the NMEA port options
window.
3. Use ▲ or ▼ to choose In/Out or In/In as
appropriate.
In/Out: Input and Output (default
setting)
In/In: Input only (Available with
connection of the GP-310B and a wind
sensor.)
4. Press ◄, choose NMEA MIX, and then
press ► to display the NMEA MIX
options window.
5. Use ▲ or ▼ to choose Off or On.
Choose On to output input data.
6. To restore normal operation, turn off the
power and then turn it on again.
Water temp/speed sensor
Connect the optional water temp/speed
sensor to the XDR connector with the
optional converter connector (Type
02S4147) as shown below.
Tape connectors with
vulcaninzing tape
and then vinyl tape
to waterproof them.
Bind tape ends with
cable ties to prevent
tape from unraveling.
Connect to XDR port
at rear of display unit
MJ-A10SPF
MJ-A10SRMDMJ-A6SRMD
From
transducer
From
sensor
Connection of converter
connector 02S4147
GP-320B
DISPLAY UNIT
GPS Receiver GP-320B
GPS Navigator GP-32,etc.
12 VDC
NMEA port setting: IN/OUT
®
¬
Connection of GP-320B

Furuno LS-6100 Specifications

General

Display	4.5" LCD
Frequency	200 kHz
Power Output	600 W
Power Supply	12-24 VDC
Type	Fish Finder
Operating Temperature	-15°C to +55°C
Beam Angle	12°

Summary

Safety Instructions for the Operator

Operator Warnings

Critical warnings for the operator to prevent hazards like shock or injury.

Operator Cautions

Precautions to prevent equipment damage or dangerous situations during operation.

Safety Instructions for the Installer

Installer Warnings

Warnings for installers regarding electrical shock, water leakage, and proper cable usage.

Installer Cautions

Cautions for installers on transducer cable handling and compass interference.

1. OPERATION

1.1 Control Description

Explains the function of each button and control on the display unit.

1.2 Turning the Power On/Off

1.4 Choosing a Display, Frequency

1.5 Menu Operating Procedure

Explains how to navigate and operate the LS-6100's menu system.

1.7 Manual Operation

1.15 Waypoints

How to record, output, and find waypoints.

1.19 Alarms

Details the six types of alarms and how to activate and configure them.

1.23 Setting Up Nav Data Displays

2. SYSTEM & INSTALLATION MENUS

2.1 System Menu

Settings for language, units, display options, and data sources.

2.2 Installation Menu

Settings for simulation, testing, memory, NMEA, and bottom level adjustments.

3. MAINTENANCE, TROUBLESHOOTING

3.1 Maintenance

3.4 Replacing the Fuse

3.6 Troubleshooting

Guide to identify and resolve common operational issues.

3.7 Diagnostics

How to run built-in diagnostic tests to check system components.

3.8 Test Pattern

4. INSTALLATION

4.1 Display Unit

4.2 Thru-hull Mount Transducer

Instructions for installing thru-hull mount transducers, including location advice.

4.3 Transom Mount Transducer

Guidance on installing transom mount transducers on boats.

4.4 Inside-hull Transducer

Procedures for mounting transducers inside the hull.

4.5 Optional Triducer

Instructions for installing the optional triducer multisensor.

4.6 Optional Water Temperature/Speed Sensor

4.7 Wiring