FUTABA 10CAP User Manual

30
$/22.$77+(5$',26)81&7,21667(3%<67(3
MODEL
submenu: includes three functions that manage model memory:
MODEL SELECT
,
MODELCOPY
and
MODELNAME
. Since
these functions are all related, and are all basic features used with most models, they are together in the
MODEL
submenu of
the
BASIC
menu.
NOTE: When you choose a new model in the
MODEL SELECT
function, if the new
model is set to the other modulation, you must cycle the transmitter power to change
PRGXODWLRQV,I\RXGRQRWF\FOHWKHSRZHUWKHPRGXODWLRQW\SHZLOOÀDVKRQWKHKRPH
screen to remind you. You are still transmitting on the other modulation until you
affect this change.
GOAL: STEPS: INPUTS:
Select Model #3.
NOTE: This is one of several
functions for which the radio requires
FRQ¿UPDWLRQWRPDNHDFKDQJH
Open
BASIC
menu, then open
MODEL
submenu.
for 1 second.
(If
ADVANCE
, again.)
C
if required to
MODEL
.
Choose Model #3.
to
3
.
&RQ¿UP\RXUFKDQJH
for 1 second.
Are you sure?
displays.
Close.
Confirm proper modulation of new
model memory.
If
PPM
,
PCM
or
2.4G
 DUH ÀDVKLQJ LQ WKH XSSHU ULJKW KDQG FRUQHU WKHQ WKH QHZ
PRGHOLVVHWIRUWKHRWKHUUHFHLYHUW\SH7XUQWKHWUDQVPLWWHURIIRQWRFKDQJHWKH
modulation.
Where next?
NAME
the model: see p. 32.
Change
MODEL TYPE
(aircraft, heli, glider): see p. 34.
Change modulation [FM (
PPM

PCM
or
2.4G-10CH

7CH
]: see p. 35.
Utilize servo
REVERSE
: see p. 38.
Adjust
END POINTs
: see p. 39.
Set up
IDLE-DOWN
and
THR-CUT
for throttle management: see p. 40, 41.
MODEL SELECT
: This function selects which of the 15 model memories in the
WUDQVPLWWHU RU  LQ WKH RSWLRQDO CAMPac-... WR VHW XS RU
À\)RUFODULW\WKHPRGHOVQDPHDQGDQLPDJHRILWVW\SHDUHLQGLFDWHGDIWHULWV
number. (Each model memory may be a different model type from the other
memories.)
T9C/T9CS CAMPac data conversion
Although a CAMPac GDWD ZKLFK VDYHG WKH GDWD RI D FRQYHQWLRQDO 7&7&6 WUDQVPLWWHU
cannot be used calling directly, it is possible to use it by the following method, copying to
the model memories of a T10C transmitter. When using the CAMPac, it will be displayed,
for example as "01<-Pac 01." Press DIAL for 1 second in this state and the check display of
"Are you sure?" will appear. Press DIAL again, the data of CAMPac will be copied to model
number"01" of the T10C transmitter. As for the data of a function added by T10C, an initial value is set up at this time.
3OHDVHGRQRWIRUJHWWKHFKHFNRIVHWWLQJGDWDEHIRUHDÀLJKW
In addition, refer to p.17 for the initializing method of the CAMPac.
Note: If you are using the optional CAMPac-16K, your choices in
MODEL SELECT
and
MODEL COPY
will include 16-19,
which are the model memories in the CAMPac. You do not have to
COPY
from the CAMPac to the transmitter prior to
working with that model
ÀDVKLQJ

FUTABA 10CAP Specifications

General

Brand	FUTABA
Model	10CAP
Category	Remote Control
Language	English