Page 43
REGULATORY NOTICES
LOCAL TELEPHONE COMPANY INTERFACE
Telephone Connection Requirements
Except for telephone company provided ringers, all connections
to the telephone network shall be made through standard plugs
and standard telephone company provided jacks or equivalent in
such a manner as to allow for immediate disconnection of the
terminal equipment. Standard jacks shall be so arranged that if
the plug connected thereto is withdrawn, no interference to the
operation of the equipment at the customers’ premises which
remains connected to the telephone network, shall occur by
reason of such withdrawal.
Incidence Of Harm
Should terminal equipment or protective circuitry cause harm to
the telephone network, the telephone company shall, where
practical, notify the customer that temporary discontinuance of
service may be required. However, where prior notice is not
practical, the telephone company may temporarily discontinue
service if such action is deemed reasonable in the circumstances.
In the case of such temporary discontinuance, the telephone
company shall promptly notify the customer who will be given
the opportunity to correct the situation. The customer also has
the right to bring a complaint to the FCC if he feels the
disconnection is not warranted.
Changes In Telephone Company Equipment Or
Facilities
The telephone company may make changes in its
communications facilities, equipment, operations, or procedures
where such action is reasonably required and proper in its
business. Should any such change render the customers terminal
equipment incompatible with the telephone company facilities,
the customer shall be given adequate notice to make
modifications to maintain uninterrupted service.
General
The FCC prohibits customer provided terminal equipment be
connected to party lines.
Importance Of The Ringer Equivalence Number
The Ringer Equivalence Number (REN) of this device is 0.1B.
This number is a representation of the electrical load that it
applies to your telephone line.
Malfunction Of The Equipment
In the event that the device should fail to operate properly, the
customer shall disconnect the equipment from the telephone line
to determine if it is the customers equipment that is not
functioning properly. If the problem is with the device, the
customer shall discontinue use until it is repaired.
Equipment Information
MANUFACTURER OF CONNECTING EQUIPMENT:
CADDX CONTROLS, INC.
FCC REGISTRATION NUMBER: GCQUSA-25950-AL-E, RINGER
EQUIVALENCE: 0.1 B
(The following applies to products which have the CE mark
attached)
CE DECLARATION OF CONFORMITY
Manufacturer’s Name: Caddx Controls
Manufacturer’s Address: 1420 North Main St.
Gladewater TX 75647
EU Representative: Interlogix Europe
Product Identification:
Product: NetworX
Model Number: NX-6
Brand: CADDX
R&TTE Directive:
See EMC and LVD tests below
EMC Directives:
EN50081-1 EN50130-4
EN55022 EN60950
EN61000-3-2 EN61000-3-3
LVD Directive: EN 60950: 1999-4 3rd edition
Means of Conformity
We declare under our sole responsibility that this product is in
conformity with Directive 1999/5/EC (R&TTE); Directive
73/23/EEC (LVD); and Directive 89/336/EEC (EMC) and based on
test results using (non)-harmonized standards in accordance with
the Directives mentioned.
Additional Tests
This equipment has been tested and found to comply with the
following standards (which are no longer required for
compliance).
Network Compatibility Declaration
We declare under our sole responsibility that this product is
designed to work with the networks in the countries marked with
a check () and may have interworking problems with the
countries that are not checked. Due to the inherent differences in
the individual PSTNs, certain software settings may need to be
adjusted on a country-to-country basis. If it is desired to use this
equipment on a network other than the one on which it was
originally installed, you should contact your equipment supplier.
() Austria
(_) Liechtenstein
() Belgium () Luxembourg
() Denmark () Netherlands
() Finland () Norway
() France () Poland
() Germany () Portugal
() Greece () Spain
() Iceland () Sweden
() Ireland () Switzerland
() Italy () United Kingdom
Telecom Approval Notice
This equipment has been approved in accordance with the
Council Decision 98/482/EC for pan-European, single terminal
connection to the public switched telephone network (PSTN).
However, due to the differences between the individual PSTNs
provided in different countries, the approval does not, of itself,
give an unconditional assurance of successful operation on every
PSTN network termination point. In the event of problems, you
should contact your equipment supplier in the first instance.
Electrical Requirements
This device automatically adjusts to voltages within the range of
230 V 50/60 Hz. Fuse: Type T 200mA 250 VAC
To Next Page
Loading...
Need help?
Operating Power
