GE NX-1308E - Caddx 8 Zone LED Keypad User Manual

NX-8 Control
14
Segment 2- Phone #1 Backup Control: Programming a "0" in Segment 2 of this location will cause the NX-8 to make
the designated number of attempts to Phone #2 before setting the "Fail To Communicate" condition and stop
reporting. Programming a "1" in this segment will cause the NX-8 to stop trying to communicate after the designated
number of attempts have been made to Phone #1. If a "2" is programmed in this segment, it will cause the NX-8 to
make the dial attempts in increments of two. The first two attempts will be made to Phone #1, the next two attempts to
Phone #2, then repeating until the total number of attempts designated in Segment 1 is completed.
COMMUNICATOR FORMAT SELECTIONS
DATA FORMAT DESCRIPTION
0 Local Communicator is disabled
1 Universal 4+2 Two digit event code 1800hz transmit 2300hz handshake double round parity
40pps
2 3+1 fast (or 4+1) One digit event code 1900Hz transmit 1400Hz handshake double round parity
20pps
3 Reserved Reserved
4 Pager 2 digit event code DTMF transmission
5 3/1 or 4/1 slow 1800hz transmit 2300hz handshake double round parity 20 p.p.s. hex capability
6 3/1 or 4/1 slow 1800hz transmit 1400hz handshake double round parity 20 p.p.s. hex capability
7 3/1 or 4/1 fast 1800hz transmit 2300hz handshake double round parity 40 p.p.s. hex capability
8 3/1 or 4/1 fast 1800hz transmit 1400hz handshake double round parity 40 p.p.s. hex capability
9 3/1 or 4/1 fast with parity 1800hz transmit 2300hz handshake single round w/parity 40 p.p.s. hex capability
10 3/1 or 4/1 fast with parity 1800hz transmit 1400hz handshake single round w/parity 40 p.p.s. hex capability
11 4+2 express 2 digit event code DTMF transmission
12 4+2 fast Two digit event code 1900hz transmit 1400hz handshake double round parity 20
p.p.s.
13 Ademco Contact ID DTMF (see pages 52-53)
14 SIA FSK (see pages 52-53)
15 Custom format (See location 18, page 18)
REPORTING EVENTS TO PHONE NUMBER 1
Phone #1 has two programming locations that are used to select which events are reported to this phone number.
Location 4 is used to select which events are reported to Phone #1. Location 5 is used to select which partitions are
reported to Phone #1. If dual or split reporting is not desired, location 4 should be used to select all events to Phone
#1 and location 5 should be left at the factory default of "0". If dual or split reporting is desired, and the split is based
on the event type (such as alarm, open/close, etc.), location 4 should be used to select only those events that should
be reported to Phone #1 and location 5 should be left at the factory default of "0". If dual or split reporting is desired,
and the split is based on partition, location 4 should be programmed as a "0" and location 5 should be used to select
those partitions that should be reported to Phone #1. If no events should be reported to Phone #1, both locations
should be programmed as "0" (disabling all options).
LOCATION 4 - EVENTS REPORTED TO PHONE # 1 (2 segments, feature selection data)
Segment 1: 1 = Alarms and Alarm Restores.
2 = Opening and Closings.
3 = Zone Bypass and Bypass Restores.
4 = Zone Trouble and Trouble Restores.
5 = Power Fail, Low Battery, Power Restore, and Low Battery Restore.
6 = Bell Cut , Telephone Line Cut, Bell Cut Restore, Telephone Line Restore.
7 = Test Reports.
8 = Start and End programming, Download complete.

GE NX-1308E - Caddx 8 Zone LED Keypad Specifications

Power

operating power	16.5 VAC 25, 40, or 50 VA Transformer
auxiliary power with 25 VA transformer	12 VDC Regulated 500 mA
auxiliary power with 40 or 50 VA transformer	12 VDC Regulated 1 AMP
auxiliary power with NX-320E power supply	12 VDC Regulated 2 AMPS
LED keypad current draw	130 mA max.
LED keypad zones normal w/o sounder	55 mA
NX-148E LCD keypad current draw	110 mA max.
NX-148E LCD keypad w/o sounder	75 mA

Operating Environment

operating temperature	32 to 120 degrees F

Loop Specifications

standard loop resistance	300 Ohms Maximum
2-wire smokes resistance	30 Ohms Maximum
loop response	Selectable 50mS or 500mS

Weight and Dimensions

LED keypad width	6.4"
LED keypad height	4.0"
LED keypad depth	1.1"
NX-148E LCD keypad width	6.4"
NX-148E LCD keypad height	5.3"
NX-148E LCD keypad depth	1.0"
metal enclosure width	11.25"
metal enclosure height	11.25"
metal enclosure depth	3.50"
shipping weight	9 lbs.