EasyManuals Logo

Gigabyte GA-MA790XT-UD4P User Manual

Gigabyte GA-MA790XT-UD4P
112 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #85 background imageLoading...
Page #85 background image
Appendix- 85 -
5-1-3 Making a SATA RAID/AHCI Driver Diskette for Windows XP
(Required for AHCI and RAID Mode)
To successfully install operating system onto SA TA hard drive(s) that is/are configured to RAID/AHCI
mode, you need to install the SATA controller driver during the OS installation. Without the driver , the
hard drive may not be recognized during the Windows setup process. First of all, copy the driver for
the SATA controller from the motherboard driver disk to a floppy disk. For installing W indows Vista, you
may directly load the SA TA RAID driver from the motherboard driver disk during the OS installation
process. For more details, refer to the next section, "5-1-3." See the instructions below about how to
copy the driver in MS-DOS mode
(Note)
. Prepare a startup disk that has CD-ROM support and two blank
formatted floppy disks.
Step 1: Insert the prepared startup disk and motherboard driver disk in your system. Boot from the startup
disk. Once at the A:\> prompt, change to your optical drive (example: D:\>). At the D:\> prompt, type the
following two commands. Press <Enter> after each command (Figure 1):
cd bootdrv
menu
Step 2: When the controller menu (Figure 2) appears, remove the startup disk and insert the blank
formatted disk. Select the controller driver by pressing the corresponding letter from the menu. For
example, from the menu in Figure 2:
For AMD SB750 SATA controllers, select 5) SB700/750 SATA for operating system
.
For GIGABYTE SATA2 SATA controller, select 1) GIGABYTE SATA-Driver(x86) for Windows 32-bit
operating system or 2) GIGABYTE SATA-Driver(x64) for W indows 64-bit operating system.
Your system will then automatically zip and transfer this driver file to the floppy disk. Press <0> to exit
when finished.
(Note) For users without a startup disk:
Use an alternative system and insert the motherboard driver disk. From your optical drive
folder, double click the MENU.exe file in the BootDrv folder (Figure 3). A command prompt
window will open similar to that in Figure 2.
Figure 1
Figure 2
Figure 3

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Gigabyte GA-MA790XT-UD4P and is the answer not in the manual?

Gigabyte GA-MA790XT-UD4P Specifications

General IconGeneral
Number of memory slots4
Maximum internal memory16 GB
Processor socketSocket AM3
Processor manufacturerAMD
USB 2.0 connectors2
Power fan connectorYes
Number of COM connectors1
Number of SATA connectors8
Controller interface typeSATA
Controller 2nd interface typeIDE
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
VGA (D-Sub) ports quantity0
Audio chipRealtek ALC889
Motherboard chipsetAMD 790X
Audio output channels7.1 channels
Motherboard form factorATX
Compatible operating systemsWindows Vista/ XP
PCI Express x1 slots3
RAID levels0, 1, 5, 10, JBOD
LAN controllerRealtek RTL8111DL
Networking features10/100/1000 Mbit/s
Weight and Dimensions IconWeight and Dimensions
Depth233 mm
Width305 mm

Related product manuals