English (GB)
2
English (GB) Installation and operating instructions
Original installation and operating instructions
These installation and operating instructions describe the
GRUNDFOS BACMON bacteria sensor.
Sections 1-5 give the information necessary to be able to handle
and install the product in a safe way.
Sections 6-13 give important information about the product, as
well as information on operating and maintaining the product,
taking it out of operation and disposing of it.
CONTENTS
Page
1. General information
This document describes the GRUNDFOS BACMON bacteria
sensor, in the following referred to as the product.
The document must be available and accessible at the
installation location at all times.
1.1 Target group
This document is intended for the operating company and the
users. It contains general instructions that must be observed
before installation and during operation and daily maintenance of
the product. The responsible staff must read these instructions
prior to any work on the product.
1.1.1 Qualification and training
The persons responsible for the tasks described in this document
must be appropriately qualified.
Operating company
The company or person owning the product or renting the product
from Grundfos is referred to as "operating company" in this
document. The operating company must coordinate the
preparation of the installation location. The installation and the
commissioning must be done by Grundfos service specialists.
Once the product is in operation, the operating company must
coordinate the regular maintenance.
Users
The persons responsible for operation and daily maintenance of
the product are referred to as "users" in this document. The users
must be trained on their tasks by the Grundfos service specialists
during commissioning, or by the operating company in agreement
with Grundfos. The users must be familiar with the product’s
operation and safety.
Grundfos service specialists
Grundfos service specialists are responsible for installation,
commissioning, parameterisation and advanced maintenance of
Grundfos products and systems. They have special knowledge,
tools and user rights to be able to perform service and repair
tasks that must not be performed by users.
1.1.2 Obligations of the operating company
• Observe the local safety regulations.
• Keep the installation and operating instructions available at
the installation location at all times.
• Coordinate the preparation of the installation location
observing section 12. Technical data.
– Provide electrical power.
– Provide a foundation for mechanical installation observing
section 4.1 Installation requirements.
– Provide a pre-treatment installation, if required. Contact
Grundfos for further information.
• Ensure that the users are trained for their tasks by the
Grundfos service specialists during commissioning.
• Provide the stipulated safety equipment and personal
protective equipment.
• Arrange regular maintenance.
1. General information
2
1.1 Target group
2
1.2 Symbols used in this document
3
1.3 Symbols on the product
3
2. Safety instructions
3
2.1 Work procedures
3
2.2 Personal protective equipment
3
3. Storing and handling the product
3
3.1 Transporting the product
3
3.2 Storing the product
3
4. Installing the product
4
4.1 Installation requirements
4
4.2 Electrical connection
4
5. Commissioning the product
4
6. Product introduction
5
6.1 Intended use
5
6.2 Identification
5
6.3 Product overview
5
6.4 Product variants and components overview
6
7. Control functions
7
7.1 Operating panel
7
7.2 Display
7
7.3 Menu
7
7.4 "Home"
7
7.5 "Status"
7
7.6 "Service"
9
8. Alarms and warnings
9
8.1 LEDs
9
8.2 Alarms and warnings
10
9. Operating the product
10
9.1 Starting and stopping the product
10
9.2 Emergency stop
10
10. Taking the product out of operation
11
10.1 Temporary decommissioning for up to 48 hours
11
10.2 Temporary decommissioning for more than 48 hours
11
10.3 Decommissioning for transport
11
10.4 Decommissioning for disposal
11
11. Maintaining the product
11
11.1 Regular maintenance
11
12. Technical data
13
12.1 Dimensions
13
12.2 Weights
13
12.3 Ambient conditions
13
12.4 Lifetime
13
12.5 Electrical data
13
12.6 Medium and hydraulic data
13
12.7 Internet connection
13
12.8 Data access
13
12.9 Measuring principle
13
12.10 Batch sample taking through flow cell
13
12.11 Built-in system diagnostics
13
12.12 Noise
13
13. Disposal
13
Prior to installation, read this document. Installation
and operation must comply with local regulations and
accepted codes of good practice.
To Next Page
Loading...
Need help?
General