To Next PageTo Next PageTo Previous PageTo Previous Page
Need help?Do you have a question about the HIKVISION Network Video Recorder and is the answer not in the manual?
General| Brand | HIKVISION |
|---|---|
| Model | Network Video Recorder |
| Category | Network Hardware |
| Language | English |
Overview of the physical control panel buttons and indicators on the NVR.
Instructions for operating the NVR using the infrared remote control.
Details on how to use a USB mouse for NVR navigation and control.
Explanation of the on-screen keyboard and input method usage.
Description of the rear panel interfaces and connectors on the NVR.
Procedures for safely powering the NVR on and off.
Step-by-step guide for initial NVR setup using the configuration wizard.
Instructions on how to add and connect IP cameras to the NVR.
Overview of the live view function and its icons.
Describes operations like single/multi-screen, auto-switch, and recording.
How to customize live view display settings like output, dwell time, and audio.
Procedure to set up PTZ camera parameters.
Configuration of PTZ presets, patrols, and patterns for camera movement.
Setting image quality, stream type, resolution, and other recording parameters.
Setting automatic recording and capture schedules.
Setting up motion detection parameters and triggering recording.
Configuring recording and capture triggered by alarm inputs.
Enabling and disabling manual and continuous recording/capture.
Methods for playing back recorded video files.
Playing back recorded video files for a specific channel.
Playing back video files recorded within a specified time duration.
Searching and playing back record files based on event types.
Using smart playback to efficiently review video containing motion or VCA information.
Procedures for exporting record files to backup devices.
Quickly exporting record files to a backup device.
Backing up record files after searching based on criteria.
Backing up event-related record files.
Selecting and exporting video clips during playback.
Procedures for backing up captured pictures.
Managing backup devices like creating folders and formatting.
Configuring motion detection parameters and alarm actions.
Setting handling actions for external sensor alarms.
Detecting video loss and configuring alarm response actions.
Detecting video tampering and configuring alarm response actions.
Receiving and handling VCA alarms from IP cameras.
Configuring handling actions for various system exceptions.
Configuring event hint, full screen monitoring, audible warning, email.
Basic network configuration including IP, gateway, DNS.
Extended network settings like PPPoE, DDNS, NTP, SNMP.
Setting up Point-to-Point Protocol over Ethernet (PPPoE) connection.
Configuring Dynamic DNS for network access.
Configuring Network Address Translation (NAT) for remote access.
Monitoring real-time network traffic status and rates.
Testing network delay, packet loss, and exporting network packets.
Setting up RAID arrays and virtual disks for data redundancy.
Quickly creating disk arrays and virtual disks.
Manually creating RAID arrays and virtual disks.
Restoring degraded arrays using hot spare disks.
Procedures for deleting virtual disks and RAID arrays.
Information on upgrading the NVR firmware.
Setting up RAID arrays on supported NVR models.
Steps to enable the RAID function on the NVR.
Quickly creating disk arrays using one-touch configuration.
Manually creating RAID arrays.
Procedure for rebuilding arrays when disks are degraded.
Steps to delete RAID arrays.
Process for initializing newly installed hard disk drives.
Adding and managing network HDDs like NAS or IP SAN.
Configuring and managing external eSATA devices.
Organizing HDDs into groups for recording and capture.
Allocating storage quotas for recorded files or pictures per camera.
Cloning HDD data to an eSATA disk.
Monitoring the status of installed HDDs.
Performing S.M.A.R.T. and bad sector detection on HDDs.
Configuring on-screen display settings like date, time, and camera name.
Setting up privacy mask zones to hide specific areas from view.
Adjusting video image parameters such as brightness and contrast.
Checking device, camera, record, alarm, network, and HDD status.
Searching and exporting system operation and alarm logs.
Importing and exporting IP camera configuration data.
Exporting NVR configuration for backup and importing to other devices.
Procedures for upgrading the NVR firmware.
Restoring the NVR to factory default settings.
Configuring parameters for the RS-232 serial port.
Adjusting general device settings like language and output resolution.
Setting up Daylight Saving Time (DST) adjustments.
Configuring additional device parameters like name and auto logout.
Managing user accounts, permissions, and access.
Steps to add new user accounts to the NVR.
