Honeywell HPFF8CM User Manual

HPFF8(E)/HPFF8CM(E) NAC Expander — P/N 53499:B4 10/1/2018 39
Connecting Multiple Units Applications
5.4 Connecting Multiple Units
Two or more HPFF8s can be connected to each other to provide additional NAC extenders for a system; see wiring in Figures 5.5–5.10.
Maintain separation of power-limited and nonpower-limited wiring as discussed in Section 2.6 on page 24.
HPFF8 System Connections
NOTE: Multiple units should not be connected in a “daisy chain” fashion. DO NOT connect a NAC output of one unit to the initiating device
signal input of the next unit. The synchronization signal will not pass unimpeded through multiple units with this wiring method.
TB3
TB4TB1
TB2
SW2
LEDs
REF+ REF– + IN – IN
+ OUT
– IN
+ OUT+ OUT
+ IN
– OUT
SIGNAL 1
SIGNAL 2
BATT+ BATT–
A+
N/O
N/C COMM
N/O
N/C C OMM
AC FAIL
TROUBL E
J1
J2
1L1 1L2 2L1 2L2
3L1 3L2
4L1 4L2A–
TB3
TB4TB1
TB2
SW2
LEDs
REF+ REF– + IN – IN
+ OUT
– IN
+ OUT+ OUT
+ IN
– OUT
SIGNAL 1 SIGNAL 2
BATT+ BATT–
A+
N/O
N/C COMM
N/O
N/C COMM
AC FAIL
TROUBLE
J1
J2
1L1 1L2 2L1 2L2
3L1 3L2
4L1 4L2A–
TB3
TB4
TB1
TB2
SW2
LEDs
REF+ REF– + IN – IN
+ OUT
– IN
+ OUT+ OUT
+ IN
– OUT
SIGNAL 1
SIGNAL 2
BATT+
BATT–
A+
N/O
N/C COMM
N/O
N/C C OMM
AC FAIL
TROUBLE
J1
J2
1L1 1L2 2L1 2L2
3L1 3L2
4L1 4L2A–
FACP
Remote Sync
or NAC
Output
conventional
to NACs
NAC Outputs
ELR or to
next units
Figure 5.5 Typical System Connections
conventional
NAC Outputs
to NACs
ELRs or to
next units
FACP
NAC Outputs
non-silenceable
silenceable
FACP
SLC
NAC Outputs
to NACs
Control Module (non-
silenceable point)
ELRs
or to
next
units
Relay Module
(silenceable
point)
HPFF8 Sync
Generator or
Pass-
Through
(Slave)
HPFF8connex-typ.wmf
HPFF8 Sync
Generator or
Pass-Through
(Slave)
(filtered if
FWR input)
HPFF8 Sync
Generator or
Pass-Through
(Slave)
(filtered if
FWR input)
TB3
TB4TB1
TB2
SW2
LEDs
REF+ REF– + IN – IN + OUT – IN + OUT+ OUT + IN – OUT
SIGNAL 1
SIGNAL 2
BATT+ BATT–
A+
N/O
N/C COMM
N/O
N/C COMM
AC FAIL
TROUBLE
J1
J2
1L1 1L2 2L1 2L2 3L1 3L2 4L1 4L2A–
TB3
TB4TB1
TB2
SW2
LEDs
REF+ REF– + IN – IN + OUT – IN + OUT+ OUT + IN – OUT
SIGNAL 1
SIGNAL 2
BATT+ BATT–
A+
N/O
N/C COMM
N/O
N/C COMM
AC FAIL
TROUBLE
J1
J2
1L1 1L2 2L1 2L2 3L1 3L2 4L1 4L2A–
TB3
TB4
TB1
TB2
SW2
LEDs
REF+ REF– + IN – IN + OUT – IN + OUT+ OUT + IN – OUT
SIGNAL 1
SIGNAL 2
BATT+
BATT–
A+
N/O
N/C COMM
N/O
N/C COMM
AC FAIL
TROUBLE
J1
J2
1L1 1L2 2L1 2L2 3L1 3L2 4L1 4L2A–
TB3
TB4TB1
TB2
SW2
LEDs
REF+ REF– + IN – IN + OUT – IN + OUT+ OUT + IN – OUT
SIGNAL 1
SIGNAL 2
BATT+ BATT–
A+
N/O
N/C COMM
N/O
N/C COMM
AC FAIL
TROUBLE
J1
J2
1L1 1L2 2L1 2L2 3L1 3L2 4L1 4L2A–
HPFF8
Pass-Through
(Slave)
(filtered if
FWR input)
Remote Sync or NAC
Output with sync
Figure 5.6 System Sync Connections
HPFF8connex-SysSync.wmf
NAC Outputs
to NACsto NACs to NACsto NACs
NAC Outputs NAC Outputs
HPFF8
Pass-Through
(Slave)
(filtered if
FWR input)
HPFF8
Pass-Through
(Slave)
(filtered if
FWR input)
HPFF8
Pass-Through
(Slave)
(filtered if
FWR input)
ELR or to
next unit
+
-
TB3
REF+ REF– + IN – IN
+ OUT
– IN
+ OUT+ OUT
+ IN
– OUT
SIGNAL 1
SIGNAL 2
+
-
TB3
REF+ REF– + IN – IN + OUT – IN + OUT+ OUT + IN – OUT
SIGNAL 1
SIGNAL 2
+
+
-
-
TB3
REF+ REF– + IN – IN + OUT – IN + OUT+ OUT + IN – OUT
SIGNAL 1
SIGNAL 2
Figure 5.7 Class B Input Connections
in from FACP or
previous FF8
ELR or out
to next unit
in from FACP or
previous FF8
ELR or out
to next unit
in from FACP or
previous FF8
in from FACP or
previous FF8
ELR or out
to next unit
ELR or out
to next unit
Ref +
Ref -
In #1 +
In #1 -
Out #1 +
Out #1 -
In #2 +
In #2 -
Out #2 +
Out #2 -
Ref +
Ref -
In #1 +
In #1 -
Out #1 +
Out #1 -
In #2 +
In #2 -
Out #2 +
Out #2 -
Ref +
Ref -
In #1 +
In #1 -
Out #1 +
Out #1 -
In #2 +
In #2 -
Out #2 +
Out #2 -
ff8connex-Binput.wmf

Honeywell HPFF8CM Specifications

General

Brand	Honeywell
Model	HPFF8CM
Category	Extender
Language	English