Honeywell LYNX Touch L5200 Series Programming Guide

- 23 -
5800 Series Transmitter Loop Numbers
LOOP 1
5806/5806W3/5807
5808/5808LST/5808W3
ENROLL AS "RF"
LOOP 1
LOOP 1
5809
ENROLL AS "RF"
581 8 MNL
ENROLL AS "RF"
LOOP 1
LOOP 1
LOOPS
1 - 3
LOOP 1
LOOP 1
5814
ENROLL AS "RF"
5800-002-V2
580 4 BD/ 5 8 04B DV
ENROLL AS "BR"
PROGRAM HOUSE ID
LOOP 4
LOOP
3
LOOP 1
LOOP 2
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
5804E
ENROLL AS "BR"
582 2 T
ENROLL AS "RF"
587 7
581 6 MN
ENROLL AS "RF"
LOOP 1
(TERMINALS)
ALTERNATE
POSITION
FOR LOOP 2
LOOP 2
(REED)
LOOP 3
(TERMINALS)
582 8 /58 2 8 V
PRO GRA M
HOUSE ID
582 1
ENROLL AS "RF"
582 0 L
ENROLL AS "RF"
581 9 S (WH S & B R S)
ENROLL AS "RF"
LOOP 1
(INTERNAL
SHOCK
SENSOR
LOOP 2
(REED)
581 9
ENROLL AS "RF"
LOOP 2
(REED)
LOOP 3
(TERMINALS)
LOOP 1
(TERMINALS)
580 0 WAV E
PRO GRA M
HOU S E ID
580 0 PIR - OD
ENR O LL AS " R F"
580 0 PIR / 580 0 PIR - C OM
ENR O LL AS " R F"
581 1
ENR O LL AS " R F"
580 0 PIR - RES
ENR O LL AS " R F"
580 0 Mic r a
ENR O LL AS " R F"
580 0 CO
ENR O LL AS " R F"
580 0 SS1
ENR OLL A S " RF"
580 0 RL
SET H O USE I D
LOOP 1
LOOP 1
(LOW
SENSITIVITY
LOOP 2
(HIGH
SENSITIVITY)
LOOP 3 (TEMP)
LOOP 4 (TAMPER)
LOOP 1
(HIGH
SECURITY)
LOOP 2
(STANDARD
SECURITY)
LOOP 3 (TILT MODE)
LOOP 4 (TAMPER)
LOOP 1
(LOW
SENSITIVITY
LOOP 2
(HIGH
SENSITIVITY)
LOOP 3 (TEMP)
LOOP 4 (TAMPER)
5834-2
ENROLL AS "BR"
5834-4
ENROLL AS "BR"
LOOP
1
LOOP
1
LOOP
1
LOOP
1
587 8
ENROLL AS "BR"
5870API
ENROLL AS "RF"
5869
ENROLL AS "RF"
585 3
ENROLL AS "RF"
ARMED
READY
MESSAGE
MIC
LOOP 1
(LOW SENSITIVITY)
LOOP 2
(HIGH SENSITIVITY)
589 8
ENROLL AS "RF"
LOOP 4
LOOP 1
LOOP 2
LOOP 3
SERIAL #1
LOOP 3
SERIAL #1
LOOP 4
SERIAL #2
LOOP 3
SERIAL #1
LOOP 2
SERIAL #1
LOOP 1
SERIAL #2
LOOP 2
3
AWAY
STAY
1
2
4
OFF
ON
SERIAL #1
LOOP 4
SERIAL #2
LOOP 1
SERIAL #2
LOOP 2
SERIAL #2
LOOP 3
SERIAL #1
LOOP 1
SERIAL #2
LOOP 4
LOOP 3
581 6
ENROLL AS "RF"
LOOP 1
(TERMINALS)
LOOP 2
(REED)
SERIAL #2
LOOP 1
SERIAL #1
LOOP 3
SERIAL #1
LOOP 2
Notes: (1) The 5806W3 smoke detector must be used in SIA applications.
(2) Button type (BR) devices send only fault and low battery signals; no restore or check-in signals.
Supervised RF (RF) devices send periodic check-in signals, faults, restore and low battery signals.
Unsupervised RF (UR) devices send periodic check-in signals, faults, restore and low battery signals but the control
does not supervise the check-in signals.
(3) If an external sounder is required, the 5800WAVE should be used.
(4) The 5804E and 5834-4 encrypted (High-Security) devices must be activated while the system is in Go/No-Go Test
Mode. Refer to the transmitter’s Installation Instruction for complete details. The system will confirm the enrollment of
the encrypted device by beeping two times
(5) The 5800PIR-OD, 5800RL, 5800SS1, 5804E, 5804BD, 5804BDV, 5814, 5816TEMP, 5821, 5828/5828V, 5877 and
5878 wireless transmitters have not been evaluated by UL/ETL
UL
ULUL
UL
The 5800RL, 5802MN, 5802MN2, 5804, 5804BD, 5804BDV, 5814, 5816TEMP, 5819, 5819S(WHS & BRS), and
5828/5828V wireless transmitters have not been evaluated by UL .

Honeywell LYNX Touch L5200 Series Specifications

General

Brand	Honeywell
Model	LYNX Touch L5200 Series
Category	Security System
Language	English