EasyManuals Logo
Home>Icom>Transceiver>IC-A14

Icom IC-A14 Service Manual

Icom IC-A14
28 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #4 background imageLoading...
Page #4 background image
1 - 1
SECTION 1 SPECIFICATIONS
P General
• Frequency coverage :
IC-A14 TX 118.000 to 136.975 MHz
RX 108.000 to 136.975 MHz
WX (Rx only) 161.650 to 163.275 MHz
IC-A14S TX/RX 118.000 to 136.975 MHz
• Mode : 6K00A3E
16K0G3E (IC-A14/Rx only)
• Channel spacing : 25 kHz
Number of memory channels :
IC-A14 200 (20 CH × 10 BANKS)
IC-A14S 100
• Power supply requirement : Specifi ed Icom’s battery packs
7.4 V DC standard
• Usable temperature range : –10˚C to +60˚C (+14°F to +140°F)
• Current drain (at 7.4 V DC) :
Tx 1.5 A
Rx at stand by 50 mA typical
at AF max. 500 mA
• Antenna connector : BNC 50 Ω (nominal)
Dimensions : 53(W) × 120(H) × 36.9(D) mm
(projections not included)
2
3
32(W) × 4
23
32(H) × 1
9
16(D) inch
Weight : Approx. 180 g (6.35 oz) (Without the battery pack and antenna.)
P Transmitter
• Output power : 5.0 W (PEP) typical
1.5 W (CW)
• Modulation : Low level modulation
• Modulation limiting : 70 to 100%
• Frequency stability : ±5 ppm
• Audio harmonic distortion : Less than 10% (at 60% mod.)
• Hum and noise ratio : More than 35 dB
• Spurious emissions : More than 46 dB (except operating frequency ±62.5 kHz range)
• External MIC connector : 3-conductor 2.5(d) mm (
1
10˝)/150 Ω
P Receiver
• Receive system : Double conversion superheterodyne
• Intermediate frequencies : 1st 46.35 MHz, 2nd 450 kHz
• Sensitivity :
COM band (6 dB S/N) –6 dBµ typical
NAVI band (6 dB S/N) –3 dBµ typical (IC-A14 only)
WX channels (12 dB SINAD) –13 dBµ typical (IC-A14 only)
• Squelch sensitivity : AM Less than 0 dBµ
(threshold) FM Less than –5 dBµ
(IC-A14 only)
• Selectivity : 6 dB (More than 7.5 kHz)
60 dB (Less than 25 kHz)
Spurious response rejection
: AM More than 60 dB
FM More than 30 dB
(IC-A14 only)
Audio output power : More than 700 mW (internal SP)
( at 10% distortion with an 8 Ω More than 500 mW (external SP)
load, 30% mod.)
• Hum and noise : More than 35 dB at 30% mod.
• External SP connector : 3-conductor 3.5 (d) mm (
1
⁄8˝)/8 Ω
All stated specifi cations are subject to change without notice or obligation.

Other manuals for Icom IC-A14

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Icom IC-A14 and is the answer not in the manual?

Icom IC-A14 Specifications

General IconGeneral
BrandIcom
ModelIC-A14
CategoryTransceiver
LanguageEnglish

Related product manuals