JUKI SC-510 User Manual

－
20
－
* Do not change the set values with asterisk (*) mark as they are functions for maintenance. If the standard set value set at the
time of delivery is changed, it is in danger of causing the machine to be broken or the performance to be deteriorated.
If it is necessary to change the set value, please purchase the Engineer’s Manual and follow the instructions.
(Descriptions of setting in this list are the standard values at the time of delivery.)
However, contents of function setting are subject to change for improvement of function and performance without notice.
4. Function setting list
No Item Description
Setting
range
Indication of function setting
Ref.
page
1 Soft start function The number of stitches to be sewn at a low speed when the soft-start
function is used at the start of sewing.
0 :
Soft-start function is not operative.
0 to 9
(Stitches)
1 0
24
2 Material end
sensor function
Material end sensor function (used in case of without panel).
0 : Material end detection function is not operative.
 1: Afterdetectingmaterialend,thespeciednumberofstitches(No.
4) will be sewn, and the sewing machine will stop.
0/1
2 0
24
3 Thread trimming
function by material
end sensor
Thread trimming function by material end sensor (used in case of with-
out panel).
0 :
Automatic thread trimming function after detection of material end
is not operative.

1: Afterdetectingmaterialend,thespeciednumberofstitches(No.
4) will be sewn, and the sewing machine will stop and perform
automatic thread trimming.
0/1
3 0
24
4 Number of
stitches for
material end
sensor
Number of stitches for material end sensor (used in case of without
panel).
Number of stitches from detection of material end to stop of the sewing
machine.
0 to 19
(Stitches)
4 5
24
5 Flicker reducing
function
Flicker
reducingfunction(Ifthehandlampickers).
0 : Flicker reducing function is not operative.
1 : Less effective
/
3 : Highly effective
0 to 3
5 0
24
6 Bobbin thread
counting function
Bobbin thread counting function
0 : Bobbin thread counting function is not operative.
1 : Bobbin thread counting function is operative.
0/1
6 1
24
7 Unit of bobbin
thread counting
down
Unit of bobbin thread counting down
0 : Count/10 stitches
1 : Count/15 stitches
2 : Count/20 stitches
0 to 2
7 0
*
8 Number of
rotation of
reverse feed
stitching
Sewing speed of reverse feed stitching
150 to 3,000
(r.p.m.)
8 1 2 0 0
9 Thread trimming
prohibiting
function
Thread trimming prohibiting function (used in case of without panel).
0 : Thread trimming prohibiting function is not operative.
1 : Thread trimming is prohibited.
(Output of solenoid is prohibited. : Thread trimmer and wiper)
0/1
9 0
24
10 Setting of needle
bar stop position
when the sewing
machine stops.
Positionofneedlebarisspeciedwhenthesewingmachinestops.
0 : Predetermined lowest position
1 : Predetermined highest position
0/1
1 0 0
25
11 Click sound of key
switch mounted
on PSC
ClicksoundofkeyswitchmountedonPSCisspecied.
0 : Click is not operative.
1 : Click is operative.
0/1
1 1 1
25
12 Optional input/
output setting
Changeover of optional switch.
1 2 O P T _
26
13 Function of
prohibiting start
of the sewing
machine by
bobbin thread
counter
Function of prohibiting start of the sewing machine by bobbin thread counting
0 : When counting is out (-1 or less) Function of prohibiting start of the sewing
machine is not operative.
1 :
When counting is out (-1 or less) Function of prohibiting start of the sewing
machine after thread trimming is operative.
2 :
When counting is out (-1 or less), the sewing machine stops once. Function
of prohibiting start of the sewing machine after thread trimming is operative.
0 to 2
1 3 0
14 Sewing counter Counting function of sewing (number of completion of process)
0 : Sewing counter function is not operative.
1 : Sewing counter function is operative.
0/1
1 4 1
30
21 Function of
neutral presser
lifting
Function of needle up/down compensating switch on the operation
panel can be changed.
0 :
Needle up/down compensation
1 : One stitch compensation
2 : Neutral automatic presser lifting is valid and the alternate motion
can be performed by depressing the pedal backward.
0/1/2
2 1 0
30
22 Function of
changeover of
compensating switch
on the operation panel
function
This function sets the thread trimming motion after DOWN position has
been off by turning handwheel by hand.
0 :
Thread trimming after turning handwheel by hand is permitted.
1 : Thread trimming after turning handwheel by hand is prohibited.
0/1
2 2 0
30
25 Thread trimming
motion condition
This function sets the thread trimming motion after DOWN position has
been off by turning handwheel by hand.
0 :
Thread trimming after turning handwheel by hand is permitted.
1 : Thread trimming after turning handwheel by hand is prohibited.
0/1
2 5 1
30

JUKI SC-510 Specifications

General

Brand	JUKI
Model	SC-510
Category	Sewing Machine
Language	English