Mitsubishi MELSEC-A A2ASCPU-S1 User Manual

2 - 10
2. SYSTEM CONFIGURATION
2.2.3 Precautions when using GPP function software packages and A8PUE peripheral devices which are
not compatible with AnU, A2AS
When starting with GPP function software packages not compatible with the AnU, A2USH-
S1, A2US, A2AS(S1), A2AS-S30 (starting with the PLC model name "A3A ", "A2A" or
"A3H") or a A8PUE peripheral device (containing A7PUS), the usable device ranges are
limited as follows.
(1) Usable device range
(a) For the A2USHCPU-S1, A2ASCPU-S30
(1) The device range other than listed above is the same as that of A2USHCPU-S1,
A2ASCPU-S30.
(2) Refer to the operation manual of each peripheral device for available functions.
Item
AnACPU-compatible module A3HCPU-compatible module
Modules whose PLC model for
system FD start-up is "A3A"
A8PUE
Modules whose PLC model for
system FD start-up is "A3H"
A7PUS
Instruction (sequence/basic/
application/dedicated)
All instructions can be used.
Program capacity A maximum of 30k steps can be used for the main program.
Number of I/O device points (X/Y)
X/Y0 to X/Y7FF can be used.
(X/Y800 to X/Y1FFF cannot be used.)
X/Y0 to X/Y7FF can be used.
(X/Y800 to X/Y1FFF cannot be used.)
M, L, S relay M/L/S0 to M/L/S8191 can be used.
M/L/S0 to M/L/S2047 can be used.
(M/L/S2048 to M/L/S8191 cannot be used.)
Link relay (B)
B0 to BFFF can be used.
(B1000 to B1FFF cannot be used.)
B0 to B3FF can be used.
(B400 to B1FFF cannot be used.)
Timer (T) T0 to T2047 can be used.
T0 to T255 can be used.
(T256 to T2047 cannot be used.)
Counter (C) C0 to C1023 can be used.
C0 to C255 can be used.
(C256 to C1023 cannot be used.)
Data register (D)
D0 to D6143 can be used.
(D6144 to D8191 cannot be used.)
D0 to D1023 can be used.
(D1024 to D8191 cannot be used.)
Link register (W)
W0 to WFFF can be used.
(W1000 to W1FFF cannot be used.)
W0 to W3FF can be used.
(W400 to W1FFF cannot be used.)
Annunciator (F) F0 to F2047 can be used.
F0 to F255 can be used.
(F256 to F2047 cannot be used.)
Index register (V, Z) V, V1 to V6, Z, Z1 to Z6 can be used.
V and Z can be used.
(V1 to V6, Z1 to Z6 cannot be used.)
Expanded comment Max. 3968 points
–
Unusable (Used on the system)
–
Latch (power failure compensation)
range
The device range shown above can be latched. The device range shown above can be latched.
I/O assignment
Possible to register occupied I/O
points and module model names.
–
Number of I/O occupied points can
be registered.
–

Mitsubishi MELSEC-A A2ASCPU-S1 Specifications

General

Brand	Mitsubishi
Model	MELSEC-A A2ASCPU-S1
Category	Controller
Language	English