To Next Page

To Previous Page

English−42

Conﬁguring the Slideshow Settings

Use the  + – and SET/POINT ZOOM buttons on the remote control to navigate the Media Player menus.

1. Navigate to the SETTINGS icon and press SET/POINT ZOOM button.

2. Navigate to [PLAY MODE] and press SET/POINT ZOOM button.

3. Select [AUTO] and press SET/POINT ZOOM button.

4. Navigate to [INTERVAL] then use the [+] and [-] buttons on the remote to adjust the amount of time an image is displayed

before switching.

This setting can be adjusted between 5 and 300 seconds.

5. Conﬁgure additional settings as needed.

• To have the slideshow repeat after the last ﬁle in the folder is displayed, press the down arrow and press SET/POINT

ZOOM button to select [REPEAT].

• To have background music play while showing still images, press the down arrow and press SET/POINT ZOOM button

to show the audio ﬁle screen. Navigate to the location where the audio ﬁle is saved, select the audio ﬁle you want to play

and then press SET/POINT ZOOM button. This will immediately return to the [MEDIA PLAYER SETTINGS] screen.

Press the down arrow and press SET/POINT ZOOM button to select BGM. If BGM does not have a check mark next to it,

the audio ﬁle you selected will not play.

• To choose what should happen when the slideshow is not set to [REPEAT], press the down arrow to [PLAY END

SCREEN] then press SET/POINT ZOOM button. Highlight the option you want and press SET/POINT ZOOM button.

• BLACK SCREEN – when the last ﬁle is played, a black screen is shown until the button on the remote is pressed.

• FILE LIST – the Media Player returns to the ﬁle list screen.

• SAVE LAST SCREEN – the slideshow pauses on the last screen, the image is displayed until the button on the

remote is pressed.

6. Navigate to [OK] and press SET/POINT ZOOM button to save the changes and return to the [MEDIA PLAYER] home screen.

NOTE:  • When the slideshow is running, the images are displayed in the ﬁles “sorted” order.

If there is a mix of both video ﬁles and still image ﬁles, the ﬁles will still play in the sorted order. The still images will

be displayed, when it gets to a video ﬁle it will play the video, when the video is done the next still image ﬁle will be

displayed.

• If an audio ﬁle is playing as background music for still image ﬁles, the music will stop when a video ﬁle is playing,

then start again when it returns to displaying still image ﬁles.

Questions and Answers:

Need help?

Do you have a question about the NEC MultiSync UN552V and is the answer not in the manual?

NEC MultiSync UN552V Specifications

General

Pixel pitch	0.63 x 0.63 mm
Response time	8 ms
Display diagonal	55 \
Display brightness	500 cd/m²
Display technology	LED
Native aspect ratio	16:9
Vertical scan range	23 - 86 Hz
Horizontal scan range	26 - 134 kHz
Contrast ratio (typical)	1700:1
Display diagonal (metric)	138.78 cm
Active display area (W x H)	1209.63 x 680.34 mm
Operating hours (hours/days)	24/7
Maximum refresh rate	60 Hz
Annual energy consumption	328 kWh
Purpose	Universal
Orientation	Horizontal/Vertical
Product color	Black
Product design	Video wall
Placement supported	Indoor
Bezel width (bottom)	0.44 mm
Panel mounting interface	400 x 400 mm
USB ports quantity	5
DisplayPorts quantity	3
Compatible memory cards	MicroSD (TransFlash)
Ethernet LAN data rates	10, 100 Mbit/s
VGA (D-Sub) input ports	1
HDMI input ports quantity	2
Audio formats supported	AAC, MP3, WAV
Image formats supported	JPG, PNG
Video formats supported	FLV, H.264, MOV, MP4, MPG, WMV
Power consumption (standby)	0.5 W
Power consumption (typical)	225 W
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	10 - 90 %
Operating relative humidity (H-H)	20 - 80 %
Certification	BSMI; CE; EAC; EMC B; FCC; PSB; RCM; REACH; RoHS; SASO; TÜV GS; TÜV S; UL/C-UL; VCCI
Sustainability certificates	RoHS
Cables included	AC, DisplayPort, HDMI
Harmonized System (HS) code	85285210