Roland Lucina AX-09 User Manual

12
Assigning the Modulation Bar’s Eect
You can also change the assignment of the modulation
bar so that it will hold notes or hold notes while applying
vibrato.
1. Hold down the [SHIFT] button and press the
modulation bar.
The current setting will blink in the display.
2. Continue to hold down the [SHIFT] button, and
use the [INC/+] / [DEC/–] (OCTAVE [+] / [–]) buttons
to assign the desired eect.
This species the eect that will be applied when you
operate the modulation bar.
Value Explanation
N o D (MODULATION)
Vibrato will be applied to the sounds you’re
playing.
h L D (HOLD)
The sounds you’re playing will be sustained
while you press the modulation bar.
C N B (COMBINATION)
Vibrato and Hold will both be applied to the
sounds you’re playing.
MEMO
The same eect is applied to all tones. However, if
you’ve selected 4 VIOLIN or 5 TROMBONE of the special
tones, the dynamics (expression) of the instrument will
be modied instead of the vibrato eect.
3. Release the [SHIFT] button.
4. To save this setting, hold down the [SHIFT] button
and press the [WRITE] button.
Using the D Beam Controller
By moving your hand above the D Beam controller’s
sensor, you can modify the sound by applying the eect
you’ve assigned to the D Beam.
The D Beam controller’s eective range
The illustration below shows the approximate eective
range of the D Beam controller.
No eect will be obtained if you position your hand
outside this eective range.
* The usable range of D Beam controller will become
extremely small when used under strong direct
sunlight. Please be aware of this when using the D Beam
controller outside.
1. Press one of the following buttons to select the
function that you want to control using the
D Beam controller.
Button Explanation
PITCH
Moving your hand above the D Beam controller
will vary the pitch of the sounds you play.
FILTER
Moving your hand above the D Beam controller
will vary the tonal character of the sounds you
play.
* For some tones, the change in character
may be dicult to notice.
ASSIGNABLE
The D Beam controller will transmit the assigned
function or control change message.
2. While you play the keyboard, move your hand
slowly up and down above the D Beam controller.
The button you pressed in step 1 will blink.
3. To turn o the D Beam controller, once again press
the button you pressed in step 1; it will go out.
Changing the ASSIGNABLE Setting
You can assign a MIDI control change number (CC) or
function to the [ASSIGNABLE] button, and use the D Beam
controller to control that parameter in real time.
1. Hold down the [SHIFT] button and press
[ASSIGNABLE].
The currently assigned function will blink in the display.
2. Continue to hold down the [SHIFT] button, and
use the [INC/+] / [DEC/–] (OCTAVE [+] / [–]) button
to specify the desired function or parameter that
will be controlled by the D Beam controller.
Display Value Explanation
C 0 1
CC01
(MODULATION)
Apply vibrato.
C 0 5
CC05
(PORTA TIME)
Control the portamento time
over which the pitch changes
between notes when playing with
portamento.
C 0 7
CC07 (VOLUME) Control the volume.
C 1 0
CC10 (PAN) Control the panning.
C 1 1
CC11 (EXPRESSION) Control the expression.
C 6 4
CC64 (HOLD) Sustain the notes.
C 6 5
CC65
(PORTAMENTO)
Smoothly connect the pitch from one
note to the next.

Roland Lucina AX-09 Specifications

General

Brand	Roland
Model	Lucina AX-09
Category	Synthesizer
Language	English