Erasing data input mistakes – 1 Erase
This function erases all the sequencer data inside the speci-
fied area. As the erased data is replaced by rests, the original
measures will remain.
Target track
Selects the track(s) or Pattern from which data will be
erased.
TRK ALL: Phrase tracks 1–16, the Beat track, and the Tempo
track
TRK 1–TRK 16: The specified Phrase track
TRK T: The Tempo track
PTN 001–PTN 100: The specified Pattern
Measure (From), for (to) (Editing area)
Specifies the area from which data will be erased.
Status
Selects the type of data to be erased.
ALL: All types of sequencer data
NOTE: Note
P.AFT: Polyphonic Aftertouch
C.C: Controller numbers
PROG: Program numbers
C.AFT: Channel Aftertouch
BEND: Pitch Bend
EXC: System Exclusive messages
TUNE: Tune Request
PTN: Pattern Call messages
✳ If the Target parameter is set to TRK T, the Status para-
meter will not be available.
Range
If you have selected NOTE, P.AFT, C.C or PROG for the
Status parameter, use this parameter to set the area.
To erase all Note or Polyphonic Aftertouch data, specify “C-
1–G9.” To erase C4 Note/Polyphonic Aftertouch data, speci-
fy “C4–C4.” To erase Note/Polyphonic Aftertouch data from
C3 to C4, specify “C3–C4.”
To erase all Controller numbers or Program numbers, speci-
fy “0–127.” To erase number 4, specify “4–4.” To erase num-
bers from 3 to 14, specify “3–14.”
Channel (MIDI channel)
Selects the MIDI channel of the data to be erased.
When you want to erase all sequencer data, set this parame-
ter to ALL. To erase sequencer data of one specific MIDI
channel only, select that MIDI channel.
✳ If you set the Target parameter to TRK T, or if the
Status parameter is set to EXC, TUNE or PTN, the
Channel parameter will not be available.
<Procedure>
❶ Make sure that the Track Edit Menu display
(SEQ/TrkEdit) is up.
❷ Press [F6] (Menu) to select Menu 1, then press [F1]
(Erase) to call up the Erase display (SEQ/TrkEdit).
This display can also be called up by moving the cursor to “1
Erase” and pressing [ENTER] on the Track Edit Menu dis-
play (SEQ/TrkEdit). Or press the numeric key [1] and press
[ENTER].
❸ Move the cursor to Target track and select the track(s)
or Pattern from which you want to erase data.
❹ When assigning the editing area by measures, move
the cursor to “Measure” and specify the measure num-
ber at which erasing will begin, then move the cursor
to “for” to specify the measure length to be erased.
When using Locate positions, press [LOCATE], and move
the cursor to “From” to select the Locate number from where
you want erasing to begin. Then move the cursor to “to” and
select the Locate number where you want erasing to end.
❺ Move the cursor to “Status” to select the data to be
erased.
If you select NOTE, P.AFT, C.C or PROG, move the cursor to
“Range” and specify the area. The key areas for NOTE or
P.AFT can be specified by pressing keys on the keyboard of
the XP-60/XP-80.
❻ Move the cursor to “Channel” and select the MIDI
channel from which you want to erase data.
❼ Press [F6] (Execute) to begin erasing.
To Next Page
Need help?
General
