SMC Networks ZSE40A User Manual

-61-
No.PS※※-OMM0007-H
Specification
■Specifications (Refer to page 63 for products with M8 (3 pin) connector)
Model No.
ZSE40A
(vacuum)
ZSE40AF
(compound)
ISE40A
(positive pressure)
Rated pressure range
0 to -101.3 kPa
-100.0 to 100.0 kPa
-0.100 to 1.000 MPa
Set pressure range
10.0 to -105.0 kPa
-105.0 to 105.0 kPa
-0.105 to 1.050 MPa
Withstand pressure
500 kPa
500 kPa
1.5 MPa
Minimum display unit
0.1 kPa
0.1 kPa
0.001 MPa
Applicable fluid
Air, inert gases and incombustible gases
Power supply voltage
12 to 24 VDC ±10%, ripple (p-p) 10% or less (protected against reverse
connection)
Current consumption
45 mA or less
Switch output
NPN or PNP open collector output, 2 outputs
Max. load current
80 mA
Max. applied voltage
28 V (NPN output)
Residual voltage
1 V or less (at 80 mA load current)
Response time
2.5 ms or less
(with anti-chatter function: 20, 100, 500, 1000 or 2000 ms)
Short circuit protection
Provided
Repeatability
±0.2%F.S. ±1 digit
Hys
teresis
Hysteresis mode
0 to variable
1
Window comparator mode
Analogue
output
Voltage
output
2
Output Voltage
(rated pressure range)
1 to 5 V ±2.5% F.S.
0.6 to 5 V
±2.5% F.S.
Linearity
±1% F.S.
Output impedance
Approx. 1 k
Current
output
3
Output current
(rated pressure range)
4 to 20 mA ±2.5% F.S.
2.4 to 20 mA
±2.5% F.S.
Linearity
±1%F.S.
Load impedance
Max. load impedance: 300  (at power supply voltage of 12 VDC)
600  (at power supply voltage of 24 VDC)
Min. load impedance: 50 
Auto-shift input
Non-voltage input (reed or solid state), Low level 0.4 V or less,
input time 5 ms or more
Display
3 1/2digits, 7-segment, dual-colour display (red/green)
Display accuracy
±2% F.S. ±1 digit (at ambient temperature 25±3 C)
Indicator LED
LED is ON when output is ON OUT1, OUT2: Orange
Environ
ment
Enclosure
IP65
Operating temp. range
Operation: -5 to 50 C, Storage: -10 to 60 C (no condensation or freezing)
Operating humidity range
Operation, Storage: 35 to 85% RH (no condensation)
Withstand voltage
1000 VAC, 1 minute between terminals and housing
Insulation resistance
50 M or more at 500 VDC between terminals and housing
Temperature characteristics
±2% F.S. (25 C reference)
Lead wire
Oil resistant vinyl cabtyre cable
5 cores 3.5, 2 m
Sectional area of conductor: 0.15 mm
2
(AWG26)
Outside diameter of insulator: 0.95 mm
Standard
CE, UL/CSA, RoHS
1: If the applied pressure fluctuates around the set value, the hysteresis must be set to more than the fluctuation width. Otherwise,
chattering will occur.
2: If analogue voltage output is selected, the analogue current output cannot be selected.
3: If analogue current output is selected, the analogue voltage output cannot be selected.

SMC Networks ZSE40A Specifications

General

Brand	SMC Networks
Model	ZSE40A
Category	Switch
Language	English