19
Menu Operations
Menu Item D: SET AUX
DESTINATION/SOURCE (for AUX
mode)
Purposes
Menu item D enables you to set source/destination names
for each source/destination select button in AUX mode.
Calling the setting display of menu item D
Press [D] on the selection display to select menu item D.
The setting display of menu item D appears.
Setting display (example)
Setting procedure
To set SET AUX DESTINATION
1
Select a button number using the cursor keys.
2
Press [Enter].
The unit enters Name Input mode.
If you press [Enter] again before entering a name,
Name Input mode is canceled.
3
a) When the setting of primary station menu item
“J: NAME STYLE” is “Type + Num”:
To set the source name and destination name, select
the type name from the list in the lower portion of the
display using [0] to [F], then enter a number.
b) When the setting of primary station menu item
“J: NAME STYLE” is “DESCRIP.NAME”:
Two input modes are available. Each time you press
[Ctrl]-[N], Description Input mode and Type + Num
Input mode are toggled.
Description Input mode: Directly enter the first 7
characters of the description name using the alphabetic
and numeric keys.
Type + Number Input mode: Enter in the same
manner as in a) above.
Note
When a description name has been specified for the
connector, the description name takes priority for
displaying the name even if you enter a type and
number name.
4
Press [Enter].
The entered name is registered.
To set SET SOURCE TABLE
1
Press [F1].
The cursor moves to the SET SOURCE TABLE block,
and the DISPLAY BUS number set for the destination
where the cursor was placed before pressing [F1]
appears at DISPLAY BUS. Settings for VIDEO and
KEY depend on the DISPLAY BUS number.
PANEL 001 through 032 and 121 through 124 are the
source names normally displayed. PANEL 033
through 064 and 125 through 128 are enabled when the
SHIFT function is set for a select button in menu item
N. PANEL 065 through 120 are not used in normal
operation.
In the SET SOURCE TABLE block, you may assign
any MVS KEYS to a select button on the panel only
one time.
2
Place the cursor to MVS KEYS to be changed using
the cursor keys.
If you press
4 at the bottom of the display, the next
page appears, and if you press
$ at the top of the
display, the previous page will appear.
3
Press [Enter].
The unit enters MVS KEYS Number Input mode. If
you press [Enter] again, this mode will be canceled.
4
Enter the number to be changed (1 through 128), then
press [Enter].
When the number change is finished, the names of
VIDEO and KEY are for the set number.
Keys assigned number 121 through 128 can be used as the
reentry buttons. When the SHIFT function is not used,
Keys 121 through 124 are used, and when the SHIFT
function is used, Keys 125 through 128 are used.
SONY ROUTING SYSTEM SETUP MENU MKS-8082 V1.00 STATION NUMBER 6
SET AUX DESTINATION CONTROL DESTINATION = OUT001
01 KEY=OUT001 02 KEY=OUT002 03 KEY=OUT003 04 KEY=OUT004
05 KEY=OUT005 06 KEY=OUT006 07 KEY=OUT007 08 KEY=OUT008
09 KEY=OUT009 10 KEY=OUT010 11 KEY=OUT011 12 KEY=OUT012
13 KEY=OUT013 14 KEY=OUT014 15 KEY=OUT015 16 KEY=OUT016
=====================================================================
SET SOURCE TABLE +-------------+-----------+
DISPLAY BUS = Main | VIDEO | KEY |
PANEL = MVS KEYS +------------+------------+
001 = 001 | IN001 | IN128 |
002 = 002 | IN002 | IN127 |
003 = 003 | IN003 | IN126 |
004 = 004 | IN004 | IN125 |
005 = 005 | IN005 | IN124 |
006 = 006 | IN006 | IN123 |
007 = 007 | IN007 | IN122 |
008 = 008 | IN008 | IN121 |
009 = 009 | IN009 | IN120 |
010 = 010 | IN010 | IN119 |
011 = 011 | IN011 | IN118 |
012 = 012 | IN012 | IN117 |
013 = 013 | IN013 | IN116 |
F1 : MOVE Ctrl-E : MENU Ctrl-D : RETURN Ctrl-N : DESCRIP. NAME
To Next Page
Loading...
Need help?
General
